Alcatel Unleashed

Hello All ,
Appreciate your support to resolve this issue
Large Rack with GD3 on slot 0 and CS-3 on slot 8 , CS-3 is working fine and GD MAC address is configured in the ethernet parameters , i can ping between CS and GD (Connectivity is ok ) .
GD continues to boot normally and then end up with the error
Download binary binmgr3 failed with three retries and then GD continues to reboot.
Lanpbxbuild is configured automatic mode .
error

"downloading /dhs3bin/downbin/mg3/binmg3 failed "

Any idea to solve this problem please ?

This is new installation (and first start)? Or old one (and something broken).

An old one that was working fine

The error says , "File not found on server or bad transfer or file corrupted" , i got a second CS that was configured on twin basis , still getting the same error.

I checked and the binmgr3 file is there , how ever if there is a way to replace this file (if that's agood option) , please explain to me

Ok may be someone can correct me : we can use pc installer as bin downloading server for int ip and gd right?
so if you judge that file is corrupted and no problem from network blocking transfert, you can find it in your OXE R.x version ISO (cdrom), just ftp (or scp) to oxe ,remove or rename the old one and put the new bin file with same rights.
which version, like this may be someone can handle it to you.

May be some problem with ftp access/credential.
Check - can you retrieve some files (f.e. accounts) via ftp with adfexc account from your PC.

haroun wrote: ↑27 Jul 2023 10:27 Ok may be someone can correct me : we can use pc installer as bin downloading server for int ip and gd right?
so if you judge that file is corrupted and no problem from network blocking transfert, you can find it in your OXE R.x version ISO (cdrom), just ftp (or scp) to oxe ,remove or rename the old one and put the new bin file with same rights.
which version, like this may be someone can handle it to you.

Thank you , i don't have the OXE file , i'm not sure wheather i can have it on the in active software part on the hard disk..will check

vad wrote: ↑27 Jul 2023 23:16 May be some problem with ftp access/credential.
Check - can you retrieve some files (f.e. accounts) via ftp with adfexc account from your PC.

Hi Vad ,
i did that , create a folder in my pc and through ftp i logged to the CS and transferred binmg3 to my PC and verified the file is transferred


See Below

250 CWD command successful.
ftp> pwd
257 "/DHS3bin/downbin/mg3" is current directory.
ftp> dir
200 PORT command successful.
150 Opening ASCII mode data connection for directory listing.
total 1600
-rw-rw-r-- 1 2011 1002 47552 Nov 9 2020 bin642xconf
-rw-rw-r-- 1 2011 1002 269 Nov 9 2020 bin642xconf.df
-rw-rw-r-- 1 2011 1002 747996 Nov 9 2020 binamcvb642x
-rw-rw-r-- 1 2011 1002 270 Nov 9 2020 binamcvb642x.df
lrwxrwxrwx 1 root 3 15 Mar 7 2001 binmg3 -> standard/binmg3
lrwxrwxrwx 1 root 3 22 Mar 7 2001 binmg3country -> standard/binmg3country
lrwxrwxrwx 1 root 3 22 Mar 7 2001 binmg3factory -> standard/binmg3factory
lrwxrwxrwx 1 root 3 20 Mar 7 2001 binmg3linux -> standard/binmg3linux
lrwxrwxrwx 1 root 3 20 Mar 7 2001 binmg3rdimg -> standard/binmg3rdimg
lrwxrwxrwx 1 root 3 20 Mar 7 2001 binmg3start -> standard/binmg3start
lrwxrwxrwx 1 root 3 20 Mar 7 2001 endmg3alone -> standard/endmg3alone
drwxr-xr-x 2 root 1002 4096 Mar 7 2001 secu
drwxr-xr-x 2 root 1002 4096 Mar 7 2001 standard
226 Transfer complete.
ftp: 1063 bytes received in 0.02Seconds 44.29Kbytes/sec.
ftp> mget binmg3
200 Type set to I.
mget binmg3? y
200 PORT command successful.
150 Opening BINARY mode data connection for binmg3 (857 bytes).
226 Transfer complete.
ftp: 857 bytes received in 0.00Seconds 857000.00Kbytes/sec.
ftp>

Run a tcpdump on the main cpu , and look at the transfer error.
Did you try to put a direct x-over cable between the 2?