6850 Creates .pmd files and rebooting continously

[ram]

Hi,

I have 4 no of 6850 switch stack in that my secondary switch was created .pmd files and rebooted again the following msg im getting in the console was given below please someone help me on this.

U-Boot (6.4.3.479.R01) (for OS6400, OS6850, and OS6855 platforms) (Mar 19 2010 -
17:59:35)

MPC8247 Reset Status: External Soft, External Hard

MPC8247 Clock Configuration
- Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core Freq 100-300
- dfbrg 0, corecnf 0x1a, busdf 3, cpmdf 1, plldf 0, pllmf 3
- vco_out 400000000, scc_clk 100000000, brg_clk 100000000
- cpu_clk 400000000, cpm_clk 200000000, bus_clk 100000000
- pci_clk 66666666

CPU: MPC8247 (HiP7 Rev 14, Mask 1.0 1K50M) at 400 MHz
Board: Alcatel OS6850 (Kite II)
I2C: ready
DRAM: 256 MB
FLASH: 8 MB
No environment variables found, using defaults

In: serial
Out: serial
Err: serial

No ethernet found.
IDE: Bus 0: OK
Device 0: Model: CF 64MB Firm: 20060729 Ser#: 2011B 0000455578
Type: Removable Hard Disk
Capacity: 62.5 MB = 0.0 GB (128000 x 512)
USB: scanning bus for devices...
USB device not responding, giving up (status=80000000)
0 USB Devices found
Hit any key to stop autoboot: 0
## Booting image at ff900000 ...
Image Name: miniboot-6.4.3.479.R01
Image Type: PowerPC VxWorks Kernel Image (gzip compressed)
Data Size: 984865 Bytes = 961.8 kB
Load Address: 00005000
Entry Point: 00005000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Ethernet MAC address not copied to NV RAM
Loading .text @ 0x01000000 (1580292 bytes)
Loading .rodata @ 0x01181d08 (337331 bytes)
Loading .data @ 0x011d42c0 (135644 bytes)
Clearing .sbss @ 0x011f54a0 (1528 bytes)
Clearing .bss @ 0x011f6000 (1571268 bytes)
## Using bootline (@ 0x4200): flash(1,0)cmm:default h=192.168.10.1 e=192.168.10.
1:ffffff00 cb=9600 cp=none cs=1 cw=8 cm=modemControlOff f=0x0
## Starting vxWorks at 0x01000000 ...
USB2 Host Stack Initialized.
USB Hub Driver Initialized
USBD Wind River Systems, Inc. 562 Initialized
M824xHCI Controller found.
Waiting to attach to USBD...Done.
usbCbiUfiDevInit() returned OK
CBI Class Driver Successfully Initialized
ataDrv call. 0 1 24 24 621 0 0
0xffffde0 (tRootTask): usbBulkDevInit() returned OK

CS EEPROM Module ID: 4201220f , System type: 48 port 1000Base-X, with 4 combo po
rts, stacking- kite2


Adding 5421 symbols for standalone.
Check Disk Running ...
dosChkLib : CLOCK_REALTIME is being reset to MON APR 23 13:00:54 2012
Value obtained from file system volume descriptor pointer: 0xed9b9d8
The old setting was THU JAN 01 00:00:00 1970
Accepted system dates are greater than THU DEC 27 00:00:00 1990
/flash/ - Volume is OK


Boot parameters are:

'flash(1,0)cmm:default e=10.255.24.81:ff000000 h=192.168.10.1 g=10.255.24.181 c
b=9600 cp=none cs=1 cw=8 cm=modemControlOff'


AOS miniboot version: 6.4.3.479.R01
VxWorks (for Alcatel CMM Motorola MPC8248) version VxWorks5.5.1
KERNEL: WIND version 2.6
Made on Mar 19 2010, 18:00:20.
Copyright Wind River Systems, Inc., 1984-2006

CPU: Motorola MPC8248. Processor #0.
Memory Size: 0x10000000 (256 MB). BSP version 1.2/1.

Attempting to load from the CERTIFIED directory...
Loading kernel from '/flash/certified/K2os.img'...
6002176
Loaded 'alcatelNetworking_kernel.lnk' from '/flash/certified/K2os.img'.
Starting at 0x100000...

USB2 Host Stack Initialized.
USB Hub Driver Initialized
USBD Wind River Systems, Inc. 562 Initialized
M824xHCI Controller found.
Waiting to attach to USBD...Done.
0xffffde0 (tRootTask): usbBulkDevInit() returned OK
usbCbiUfiDevInit()Creturned OK
CBI Class Driver Successfully Initialized
ataDrv call. 0 1 24 24 621 0 0

Adding 10619 symbols for standalone.
heck Disk Running ...
dosChkLib : CLOCK_REALTIME is being reset to MON APR 23 13:04:30 2012
Value obtained from file system volume descriptor pointer: 0xf58b2a0
The old setting was THU JAN 01 00:00:00 1970
Accepted system dates are greater than THU DEC 27 00:00:00 1990
/flash/ - Volume is OK


Boot parameters are:

'flash(1,0)cmm:default e=10.255.24.81:ff000000 h=192.168.10.1 g=10.255.24.181 c
b=9600 cp=none cs=1 cw=8 cm=modemControlOff'


AOS kernel version: 6.4.4.402.R01
VxWorks (for Alcatel CMM Motorola MPC8248) version VxWorks5.5.1
KERNEL: WIND version 2.6
Made on Oct 10 2011, 19:15:34.
Copyright Wind River Systems, Inc., 1984-2006

CPU: Motorola MPC8248. Processor #0.
Memory Size: 0x10000000 (256 MB). BSP version 1.2/1.

Portions of code copyrighted by Agranat Systems, Inc. All Rights reserved
Portions of code copyrighted by Alcatel-Lucent 1994-2011. All Rights reserved
Portions of code copyrighted by Apptitude, Inc. 1997-1999. All Rights reserved
Portions of code copyrighted by Free Software Foundation, Inc. 1989,1991. All r
ights reserved
Portions of code copyrighted by The OpenLDAP Foundation 1999-2000. All rights r
eserved
Portions of code copyrighted by Theodore T'so 1994,1995,1996,1997,1998,1999. Al
l Rights reserved
Portions of code copyrighted by RSA Security, Inc. All Rights reserved
Portions of code copyrighted by Sun Microsystems, Inc. All Rights reserved
Portions of code copyrighted by Wind River Systems, Inc. All Rights reserved
Portions of code developed by the University of California, Berkeley.
Portions of code developed by the Carnegie-Mellon University.


0xffffde0 (tRootTask): cmm_random_init OK
0xf577508 (tWhirlpool): batch_entropy_process called
Target Name: vxTarget
User: target
Attaching network interface lo0... done.

The current date and time is:
Coordinated Universal Time (UTC): MON APR 23 13:04:37 2012
Local time: MON APR 23 13:04:37 2012 GMT

Starting dynamic software load from '/flash/certified/'...
7fb0ceaeeef888ecbd7366e4c2381258691545d4

MON APR 23 13:04:49 : SYSTEM (75) info message:
+++ Switch Logging device '/dev/console' enabled for output

MON APR 23 13:04:49 : CSM-CHASSIS (103) info message:
+++ == CSM == === Chassis Supervision Starting Up ===
sysStartWatchdog() Starting watchdog timer to INTERRUPT after 240 secs.
Transferring crash data to a file ...


**** All the crash files are already available.Overwriting Crash4.pmd file ****
Transferring PMD done...
BCMINIT ERROR: Unable to find device profile for modType 4201220f device b500
Ni Sup & Prober: Exit code 6


Dumping PMD..... KITE/ETNA/GARUDA


tNiSup&Prb (de00ec8) @ 40 READY lckd=0 EE ME DS stk de00ec8-ddfe3d0
(de00e68) 327af4 327af4: fe2154()
(de00e28) fe2154 fe2154: fe37f0()
(de00e10) fe37f0 fe37f0: fe3c04()
(de00d90) fe3c04 fe3c04: 148068()
(de00d68) 148068 148068: 328e5c()
Writing PMD to flash ...size 259bytes and block 0
Writing PMD to flash ...size 882bytes and block 0
Writing PMD to flash ...size 1546bytes and block 0
Writing PMD to flash ...size 3671bytes and block 0
Writing PMD to flash ...size 3790bytes and block 0
Writing PMD to flash ...size 3856bytes and block 0
Writing PMD to flash ...size 5449bytes and block 0
Writing PMD to flash ...size 26001bytes and block 0
Writing PMD to flash ...size 26509bytes and block 0
Writing PMD to flash ...size 30165bytes and block 0
Writing PMD to flash ...size 47588bytes and block 0
Writing PMD to flash ...size 131060bytes and block 1
Writing PMD to flash ...size 262132bytes and block 2
Writing PMD to flash ...size 310445bytes and block 2
Dumping sys trace to PMD
Writing PMD to flash ...size 334865bytes and block 2
Writing PMD to flash ...size 343087bytes and block 2
Dumping ttall to PMD
Writing PMD to flash ...size 368023bytes and block 2
Dumping application data to PMD Start
cDumping application data to PMD Done

Writing PMD to flash ...size 385176bytes and block 2
Dumping spy report to PMD
Writing PMD to flash ...size 387850bytes and block 2
Writing PMD to flash ...size 387850bytes and block 2
Completed PMD dump system rebooting...
ha

U-Boot (6.4.3.479.R01) (for OS6400, OS6850, and OS6855 platforms) (Mar 19 2010 -
17:59:35)

MPC8247 Reset Status: External Soft, External Hard

MPC8247 Clock Configuration
- Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core Freq 100-300
- dfbrg 0, corecnf 0x1a, busdf 3, cpmdf 1, plldf 0, pllmf 3
- vco_out 400000000, scc_clk 100000000, brg_clk 100000000
- cpu_clk 400000000, cpm_clk 200000000, bus_clk 100000000
- pci_clk 66666666

CPU: MPC8247 (HiP7 Rev 14, Mask 1.0 1K50M) at 400 MHz
Board: Alcatel OS6850 (Kite II)
I2C: ready
DRAM: 256 MB
FLASH: 8 MB
No environment variables found, using defaults

In: serial
Out: serial
Err: serial

No ethernet found.
IDE: Bus 0: OK
Device 0: Model: CF 64MB Firm: 20060729 Ser#: 2011B 0000455578
Type: Removable Hard Disk
Capacity: 62.5 MB = 0.0 GB (128000 x 512)
USB: scanning bus for devices...
USB device not responding, giving up (status=80000000)
0 USB Devices found
Hit any key to stop autoboot: 0
## Booting image at ff900000 ...
Image Name: miniboot-6.4.3.479.R01
Image Type: PowerPC VxWorks Kernel Image (gzip compressed)
Data Size: 984865 Bytes = 961.8 kB
Load Address: 00005000
Entry Point: 00005000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Ethernet MAC address not copied to NV RAM
Loading .text @ 0x01000000 (1580292 bytes)
Loading .rodata @ 0x01181d08 (337331 bytes)
Loading .data @ 0x011d42c0 (135644 bytes)
Clearing .sbss @ 0x011f54a0 (1528 bytes)
Clearing .bss @ 0x011f6000 (1571268 bytes)
## Using bootline (@ 0x4200): flash(1,0)cmm:default h=192.168.10.1 e=192.168.10.
1:ffffff00 cb=9600 cp=none cs=1 cw=8 cm=modemControlOff f=0x0
## Starting vxWorks at 0x01000000 ...
USB2 Host Stack Initialized.
USB Hub Driver Initialized
USBD Wind River Systems, Inc. 562 Initialized
M824xHCI Controller found.
Waiting to attach to USBD...Done.
usbCbiUfiDevInit() returned OK
CBI Class Driver Successfully Initialized
ataDrv call. 0 1 24 24 621 0 0
0xffffde0 (tRootTask): usbBulkDevInit() returned OK

CS EEPROM Module ID: 4201220f , System type: 48 port 1000Base-X, with 4 combo po
rts, stacking- kite2


Adding 5421 symbols for standalone.
Check Disk Running ...
dosChkLib : CLOCK_REALTIME is being reset to MON APR 23 13:04:50 2012
Value obtained from file system volume descriptor pointer: 0xed9b9d8
The old setting was THU JAN 01 00:00:00 1970
Accepted system dates are greater than THU DEC 27 00:00:00 1990
/flash/ - Volume is OK


Boot parameters are:

'flash(1,0)cmm:default e=10.255.24.81:ff000000 h=192.168.10.1 g=10.255.24.181 c
b=9600 cp=none cs=1 cw=8 cm=modemControlOff'


AOS miniboot version: 6.4.3.479.R01
VxWorks (for Alcatel CMM Motorola MPC8248) version VxWorks5.5.1
KERNEL: WIND version 2.6
Made on Mar 19 2010, 18:00:20.
Copyright Wind River Systems, Inc., 1984-2006

CPU: Motorola MPC8248. Processor #0.
Memory Size: 0x10000000 (256 MB). BSP version 1.2/1.

Attempting to load from the CERTIFIED directory...
Loading kernel from '/flash/certified/K2os.img'...
6002176
Loaded 'alcatelNetworking_kernel.lnk' from '/flash/certified/K2os.img'.
Starting at 0x100000...

USB2 Host Stack Initialized.
USB Hub Driver Initialized
USBD Wind River Systems, Inc. 562 Initialized
M824xHCI Controller found.
Waiting to attach to USBD...Done.
0xffffde0 (tRootTask): usbBulkDevInit() returned OK
usbCbiUfiDevInit()Creturned OK
CBI Class Driver Successfully Initialized
ataDrv call. 0 1 24 24 621 0 0

Adding 10619 symbols for standalone.
heck Disk Running ...
dosChkLib : CLOCK_REALTIME is being reset to MON APR 23 13:08:24 2012
Value obtained from file system volume descriptor pointer: 0xf58b2a0
The old setting was THU JAN 01 00:00:00 1970
Accepted system dates are greater than THU DEC 27 00:00:00 1990
/flash/ - Volume is OK


Boot parameters are:

'flash(1,0)cmm:default e=10.255.24.81:ff000000 h=192.168.10.1 g=10.255.24.181 c
b=9600 cp=none cs=1 cw=8 cm=modemControlOff'


AOS kernel version: 6.4.4.402.R01
VxWorks (for Alcatel CMM Motorola MPC8248) version VxWorks5.5.1
KERNEL: WIND version 2.6
Made on Oct 10 2011, 19:15:34.
Copyright Wind River Systems, Inc., 1984-2006

CPU: Motorola MPC8248. Processor #0.
Memory Size: 0x10000000 (256 MB). BSP version 1.2/1.

Portions of code copyrighted by Agranat Systems, Inc. All Rights reserved
Portions of code copyrighted by Alcatel-Lucent 1994-2011. All Rights reserved
Portions of code copyrighted by Apptitude, Inc. 1997-1999. All Rights reserved
Portions of code copyrighted by Free Software Foundation, Inc. 1989,1991. All r
ights reserved
Portions of code copyrighted by The OpenLDAP Foundation 1999-2000. All rights r
eserved
Portions of code copyrighted by Theodore T'so 1994,1995,1996,1997,1998,1999. Al
l Rights reserved
Portions of code copyrighted by RSA Security, Inc. All Rights reserved
Portions of code copyrighted by Sun Microsystems, Inc. All Rights reserved
Portions of code copyrighted by Wind River Systems, Inc. All Rights reserved
Portions of code developed by the University of California, Berkeley.
Portions of code developed by the Carnegie-Mellon University.


0xffffde0 (tRootTask): cmm_random_init OK
0xf577508 (tWhirlpool): batch_entropy_process called
Target Name: vxTarget
User: target
Attaching network interface lo0... done.

The current date and time is:
Coordinated Universal Time (UTC): MON APR 23 13:08:32 2012
Local time: MON APR 23 13:08:32 2012 GMT

Starting dynamic software load from '/flash/certified/'...
7fb0ceaeeef888ecbd7366e4c2381258691545d4

MON APR 23 13:08:44 : SYSTEM (75) info message:
+++ Switch Logging device '/dev/console' enabled for output

MON APR 23 13:08:44 : CSM-CHASSIS (103) info message:
+++ == CSM == === Chassis Supervision Starting Up ===
sysStartWatchdog() Starting watchdog timer to INTERRUPT after 240 secs.
Transferring crash data to a file ...


**** All the crash files are already available.Overwriting Crash4.pmd file ****
Transferring PMD done...
BCMINIT ERROR: Unable to find device profile for modType 4201220f device b500
Ni Sup & Prober: Exit code 6


Dumping PMD..... KITE/ETNA/GARUDA


tNiSup&Prb (de00ec8) @ 40 READY lckd=0 EE ME DS stk de00ec8-ddfe3d0
(de00e68) 327af4 327af4: fe2154()
(de00e28) fe2154 fe2154: fe37f0()
(de00e10) fe37f0 fe37f0: fe3c04()
(de00d90) fe3c04 fe3c04: 148068()
(de00d68) 148068 148068: 328e5c()
Writing PMD to flash ...size 259bytes and block 0
Writing PMD to flash ...size 885bytes and block 0
Writing PMD to flash ...size 1549bytes and block 0
Writing PMD to flash ...size 3674bytes and block 0
Writing PMD to flash ...size 3793bytes and block 0
Writing PMD to flash ...size 3859bytes and block 0
Writing PMD to flash ...size 5452bytes and block 0
Writing PMD to flash ...size 26004bytes and block 0
Writing PMD to flash ...size 26512bytes and block 0
Writing PMD to flash ...size 30916bytes and block 0
Writing PMD to flash ...size 48339bytes and block 0
Writing PMD to flash ...size 131060bytes and block 1
Writing PMD to flash ...size 262132bytes and block 2
Writing PMD to flash ...size 311645bytes and block 2
Dumping sys trace to PMD
Writing PMD to flash ...size 336065bytes and block 2
Writing PMD to flash ...size 344287bytes and block 2
Dumping ttall to PMD
Writing PMD to flash ...size 369223bytes and block 2
Dumping application data to PMD Start
cDumping application data to PMD Done

Writing PMD to flash ...size 386376bytes and block 2
Dumping spy report to PMD
Writing PMD to flash ...size 389050bytes and block 2
Writing PMD to flash ...size 389050bytes and block 2
Completed PMD dump system rebooting...


Regards,
Ram

[lmherdvera]

hi, i also have a switch getting this error..any help please...thank you...

[silvio]

try usb disaster recovery
Befor it you should format the filesystem.
interupt boot - start at miniboot
[Miniboot]-> diskFormat
[Miniboot]-> diskInit
[Miniboot]-> sysNewfs “/flash”
[Miniboot]-> reboot

You will find some hints for it in the forum.
regards
Silvio