password recovery or reset

[wael]

dear all
I need to recover or restet the password of alcatel-lucent 6400 switch
i tried the following:
=>fatls ide :1,0
and i receive the following message: unable to ide 0:1 for fatls **

so any help please !!!!!!!!
best regards

[one6f]

Hi,
USB Recovery AOS
OS-6400 Recovery via ZMODEM
AOS recovery and Zmodem procedure

[jlettinck]

Password Recovery Procedure
OmniSwitch 6400 series
Power on the OmniSwitch 6400 and wait for the "Hit any key to stop autoboot" message
(Press any key...)
U-Boot (6.3.3.276.R01) (for OS6400, OS6850, and OS6855 platforms) (Aug 5 2008 - 15:13:11)
MPC8247 Reset Status: External Soft, External Hard
MPC8247 Clock Configuration
- Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core Freq 100-300
- dfbrg 0, corecnf 0x1a, busdf 3, cpmdf 1, plldf 0, pllmf 3
- vco_out 400000000, scc_clk 100000000, brg_clk 100000000
- cpu_clk 400000000, cpm_clk 200000000, bus_clk 100000000
- pci_clk 66666666
CPU: MPC8247 (HiP7 Rev 14, Mask 1.0 1K50M) at 400 MHz
Board: Alcatel OS6400 (Garuda)
I2C: ready
DRAM: 256 MB
FLASH: 128 MB
In: serial
Out: serial
Err: serial
No ethernet found.
Hit any key to stop autoboot: 0
=>
=>
You are now in the U-Boot CLI - enter the following two commands to boot into Miniboot
=>
=> setenv bootflags 0x1000
=> bootm 0xff900000
## Booting image at ff900000 ...
Image Name: miniboot-6.3.3.276.R01
Image Type: PowerPC VxWorks Kernel Image (gzip compressed)
Data Size: 864851 Bytes = 844.6 kB
Load Address: 00005000
Entry Point: 00005000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Ethernet MAC address not copied to NV RAM
Loading .text @ 0x01000000 (1317152 bytes)
Loading .rodata @ 0x01141920 (276283 bytes)
Loading .data @ 0x01185060 (122004 bytes) Alcatel-Lucent Enterprise 2/4
Clearing .sbss @ 0x011a2cf8 (1696 bytes)
Clearing .bss @ 0x011a4000 (1578044 bytes)
## Using bootline (@ 0x4200): tffs(0,0)lanswitch:default h=192.168.10.1
e=192.168.10.1:ffffff00 cb=9600 cp=none cs=1 cw=8 cm=modemControlOff f=0x1000
## Starting vxWorks at 0x01000000 ...
CS EEPROM Module ID: 42012283 , System type: 24 port Fiber 1000Base-x, with 4 combo ports,
Stacking - Garuda
TFFS detected, mounting TFFS file system
Adding 5197 symbols for standalone.
Boot parameters are:
'tffs(0,0)lanswitch:default e=10.255.24.81:ff000000 h=192.168.10.1 g=10.255.24.181
f=0x1000 cb=9600 cp=none cs=1 cw=8 cm=modemControlOff'
AOS miniboot version: 6.3.3.276.R01
VxWorks (for Freescale MPC8248) version VxWorks5.5.1
KERNEL: WIND version 2.6
Made on Aug 5 2008, 17:01:48.
Copyright Wind River Systems, Inc., 1984-2006
CPU: Freescale MPC8248. Processor #0.
Memory Size: 250 MBytes. BSP version 1.2/1.
Portions of code copyrighted by Agranat Systems, Inc. All Rights reserved
Portions of code copyrighted by Alcatel Internetworking, Inc. 1994-2008. All Rights
reserved
Portions of code copyrighted by Apptitude, Inc. 1997-1999. All Rights reserved
Portions of code copyrighted by Free Software Foundation, Inc. 1989,1991. All rights
reserved
Portions of code copyrighted by The OpenLDAP Foundation 1999-2000. All rights reserved
Portions of code copyrighted by Theodore T'so 1994,1995,1996,1997,1998,1999. All Rights
reserved
Portions of code copyrighted by RSA Security, Inc. All Rights reserved
Portions of code copyrighted by Sun Microsystems, Inc. All Rights reserved
Portions of code copyrighted by Wind River Systems, Inc. All Rights reserved
Portions of code developed by the University of California, Berkeley.
Portions of code developed by the Carnegie-Mellon University. Alcatel-Lucent Enterprise 3/4
Running fsck ....
/flash/ - Volume is OK
WARNING: Stopping in miniboot as directed by boot flags...
[Miniboot]->
From Miniboot you need to delete the "userTable5" file in /flash/network
[Miniboot]->
[Miniboot]->cd "network"
value = 0 = 0x0
[Miniboot]->ls
.
..
userTable5
lockoutSetting
policy.cfg
ssh_host_dsa_key
ssh_host_dsa_key.pub
value = 0 = 0x0
[Miniboot]->xdelete "userTable5"
value = 0 = 0x0
[Miniboot]->ls
.
..
lockoutSetting
policy.cfg
ssh_host_dsa_key
ssh_host_dsa_key.pub
value = 0 = 0x0
From Miniboot reboot into AOS and login with user "admin" password "switch"
[Miniboot]->reboot
WARNING: "sysResetHardwareFlag" flag is SET, forcing CMM board reset.
U-Boot (6.3.3.276.R01) (for OS6400, OS6850, and OS6855 platforms) (Aug 5 2008 - 15:13:11)
MPC8247 Reset Status: External Soft, External Hard
MPC8247 Clock Configuration
.... <snipped out boot process>
login :
login : admin
password : switch

Welcome to the Alcatel-Lucent OmniSwitch 6400
Software Version 6.3.3.277.R01 GA, August 06, 2008.
Copyright(c), 1994-2008 Alcatel-Lucent. All Rights reserved.
OmniSwitch(TM) is a trademark of Alcatel-Lucent registered
in the United States Patent and Trademark Office.

->
->

[toantxqti]

=> setenv bootflags 0x1000
=> bootm 0xff900000
## Booting image at ff900000 ...
Image Name: miniboot-6.4.3.565.R01
Image Type: PowerPC VxWorks Kernel Image (gzip compressed)
Data Size: 1006719 Bytes = 983.1 kB
Load Address: 00005000
Entry Point: 00005000
Verifying Checksum ... Bad Data CRC <<--------------