Is incoming call from the PSTN through cisco gateway 2811 with 2 E1 board, 1 to the PSTN a another to A4400 QSig, and the destination Called is a CCD Pilot. The problem is, Alcatel don't send the connect when connect to tha Voice Guide, and after a public timout the call is disconnect.
______________________________________________________________________________
| (156767:215906) Physical-Event :
| long: 77 desti: 0 source: 0 cryst: 0 cpl: 6 us: 0 term: 0 type a5
| tei: 0 >>>> message received : SETUP [05] Call ref : 13 bd
| SENDING COMPLETE
|______________________________________________________________________________
|
| IE:[04] BEARER_CAPABILITY (l=3) 80 90 a3
| IE:[18] CHANNEL (l=3) a9 83 9b -> T2 : B channel 27 exclusive
| IE:[1c] FACILITY (l=22)
| [91] Discriminator of supplementary service applications
| [aa] NFE (l=6):
| [80] Source Entity (l=1) End_PTNX
| [82] Destination Entity (l=1) End_PTNX
| [a1] INVOKE (l=11):
| Invoke Ident. : 0000 (0)
| OP: ECMA RO_CALLING_NAME (0)
| [84] Name not available (l=0)
| IE:[1e] PROGRESS_ID (l=2) 80 83
| IE:[6c] CALLING_NUMBER (l=11) -> 09 83 Num : 214389752
| IE:[70] CALLED_NUMBER (l=5) -> 89 Num : 3900
|______________________________________________________________________________
______________________________________________________________________________
| (156767:215908) 96: Send_IO1 (link-nbr=6, sapi=0, tei=0) :
| long: 23 desti: 0 source: 15 cryst: 0 cpl: 6 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : CALL PROC (02) Call ref : 93 bd
|______________________________________________________________________________
|
| IE:[18] CHANNEL (l=3) a1 83 9b -> T2 : B channel 27 preferred
|______________________________________________________________________________
______________________________________________________________________________
| (156767:215909) 96: Send_IO1 (link-nbr=6, sapi=0, tei=0) :
| long: 22 desti: 0 source: 15 cryst: 0 cpl: 6 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : ALERT (01) Call ref : 93 bd
|______________________________________________________________________________
|
| [95] Locking shift. codeset : 5
| IE:[32] EI_PARTY_CATEGORY (l=1) -> EXTENSION (1)
|______________________________________________________________________________
______________________________________________________________________________
| (156767:215910) 96: Send_IO1 (link-nbr=6, sapi=0, tei=0) :
| long: 22 desti: 0 source: 15 cryst: 0 cpl: 6 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : PROGRESS (03) Call ref : 93 bd
|______________________________________________________________________________
|
| IE:[1e] PROGRESS_ID (l=2) 80 88
|______________________________________________________________________________
can you help me?
A4400 R4.1 Qsig with Cisco CUCM
That should be enough for CISCO or PSTN switch - they should connect B-channel so calling sbs hears voice guide.jmmcdias wrote: ______________________________________________________________________________
| (156767:215910) 96: Send_IO1 (link-nbr=6, sapi=0, tei=0) :
| long: 22 desti: 0 source: 15 cryst: 0 cpl: 6 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : PROGRESS (03) Call ref : 93 bd
|______________________________________________________________________________
|
| IE:[1e] PROGRESS_ID (l=2) 80 88
|______________________________________________________________________________
Check with CISCO or PSTN.
If it looks like a duck, swims like a duck, and quacks like a duck, then it probably is a duck.
Alex wrote:That should be enough for CISCO or PSTN switch - they should connect B-channel so calling sbs hears voice guide.
Check with CISCO or PSTN.
YES, I hears the voice guide, but was you now, the PSTN if don't receive a CONNECT after a timout DISCONNECT the call. that is the problem.
we have doing a Workaround, we put Cisco answer the call before go to the CCD.
-
benny
jmmcdias wrote:YES, I hears the voice guide, but was you now, the PSTN if don't receive a CONNECT after a timout DISCONNECT the call. that is the problem.
we have doing a Workaround, we put Cisco answer the call before go to the CCD.
Exactly - PSTN disconnects the call. Because your have QSIG between OXE and CISCO and EDSS1 between CISCO and PSTN. These protocols differ in some aspects.
After receiving ALERT PSTN should wait at least 30 seconds before releasing a connection. Anyway how long is you VG?
If it looks like a duck, swims like a duck, and quacks like a duck, then it probably is a duck.
Strange.jmmcdias wrote:this is a CCD, for that, the VG depend if the client have free agent or not, and we have the problem because after 16h the client have allot of calls, when A4400 was connected to the PSTN we didn't have problems because she sent the CONNECT when entering in Voice Guide
So it would be better provide full trace - until PTT disconnects the call. Also do trace Cisco-PSTN connection too. Compare traces. As I told you, looks like Cisco is not properly doing transit call from QSIG to EDSS1.
By the way, which exact SW version of 4400 do yo have?
If it looks like a duck, swims like a duck, and quacks like a duck, then it probably is a duck.
