Unable to read the EEPROM - ABORT !

[Motello123]

Hi all, this week started in a very bad way.
During an upgrade on my 6450, an AC interruption occured.

The switch rebooted when the energy power come back.
Now the switch can't load the firmware image, and tells me that message "Unable to read the EEPROM - ABORT !"

The only thing i can do is use the miniboot.

What i can do?

Thanks.

[Miri1400]

Hi
Did you solve your problem???
I have this problem too...

[patg]

Same here.. is there a way to reprogram FPGA from miniboot or uboot ?

[jblimeira]

Same here:

Code: Select all

AOS BootSelector Version: 6.6.3.259.R01

Creation Date: Mar 21 2012 23:07:59.

Press x to choose XMODEM...

Press s to STOP AT MINIBOOT...

Reading kfminiboot.bs from /boot ...done:
1572800

Uncompressed kfminiboot.bs @ 0xA10000...
Running Miniboot...

Detected board DB-98DX4122-48G
Ctrl env init... Done.
CPU if init..... Done.
Done. Actual freq = 96153Hz
Memory on board initialized .

Init Phy port 0 .. Done

Init Phy port 1 .. Done
Power up GMII port0 .. Done.
Power up GMII port1 .. Done.


Detected DRAM size 256MB
Detect SysClk  320MHz
Detect Tclk    200MHz
Marvell Controller initialization Done.
Eth int Ctrl.... Done
GPIO int Ctrl... Done
PEX int Ctrl.... Done
PEX0 init....... Done. DEVICE type selected
USB Init........ Done
USB int Ctrl.... Done
XOR int Ctrl.... Done
XOR init........ Done
mvCtrlInit2..... done
PCI auto config. done
sysHwInit2...... DoneUSB2 Host Stack Initialized.
USB Hub Driver Initialized
USBD  Wind River Systems, Inc. 560 Initialized
Non-PCI USB device found: pgmIf=0xa0, idx=0 , baseAddr=0xf1050100, irq=19, swapFunc=0xa1abf4
EHCI Controller found.
Waiting to attach to USBD...Done.
0xffffe50 (tRootTask): usbBulkDevInit() returned OK
usbCbiUfiDevInit() returned OK
CBI Class Driver Successfully Initialized
i2cInit:FAILURE: Channel Map not inited for modelId[0x0]
sysCheckModId CS EEPROM read FAILURE!!!

System Configuration

BSP Ver: 1.2/1.1.01   Creation date: Dec  5 2017, 04:43:46
CHIP   : MV88F6281 Rev 2
CPU    : ARM926 (Rev 1)
BOARD  : DB-98DX4122-48G (0x7)
CLOCKs : tClk =  200 MHz, sysClk =  320 MHz
         pClk =  800 MHz

NAT_SUPPORT         = Disabled
VFP_SUPPORT         = Disabled
Target Name: vxTarget
Ethernet port #0 initialized
mgi0 Interface Loaded
mgi0 Interface Started
mgi0 Interface - Link Up, 1000 Full
Attaching network interface lo0... done.
mgi0 Interface - Link Up, 1000 Full

Adding 8194 symbols for standalone.


Boot parameters are:

flash(0,0)cmm:default e=10.4.50.165:ff000000 g=10.4.50.5 u=admin cb=9600 cp=none cs=1 cw=8 cm=modemControlOff


AOS miniboot version: 6.7.2.107.R03
VxWorks (for DB-98DX4122-48G BE MMU ARCH 5) version VxWorks5.5.1
KERNEL: WIND version 2.6
Made on Dec  5 2017, 04:43:46.
Copyright Wind River Systems, Inc., 1984-2006

CPU: DB-98DX4122-48G BE MMU ARCH 5.  Processor #0.
Memory Size: 256 MBytes.  BSP version 1.2/1.1.01.

Portions of code copyrighted by Agranat Systems, Inc.  All Rights reserved
Portions of code copyrighted by ALE USA Inc., 2015. All Rights reserved
Portions of code copyrighted by Alcatel Internetworking, Inc. 1994-2014.  All Rights reserved
Portions of code copyrighted by Apptitude, Inc. 1997-1999.  All Rights reserved
Portions of code copyrighted by Free Software Foundation, Inc. 1989,1991.  All rights reserved
Portions of code copyrighted by The OpenLDAP Foundation 1999-2000.  All rights reserved
Portions of code copyrighted by Theodore T'so 1994,1995,1996,1997,1998,1999.  All Rights reserved
Portions of code copyrighted by RSA Security, Inc.  All Rights reserved
Portions of code copyrighted by Sun Microsystems, Inc.  All Rights reserved
Portions of code copyrighted by Wind River Systems, Inc.  All Rights reserved
Portions of code developed by the University of California, Berkeley.
Portions of code developed by the Carnegie-Mellon University.


sysInitializeTimezoneInfoInNvRam() failed.
RTC get failed ffffa38
Attempting to load from the CERTIFIED directory...
Loading kernel from '/flash/certified/KFos.img'...
9239328
Loade
Detected board DB-98DX4122-48G
Ctrl env init... Done.
CPU if init..... Done.
Done. Actual freq = 96153Hz
Memory on board initialized .

Init Phy port 0 .. Done

Init Phy port 1 .. Done
Power up GMII port0 .. Done.
Power up GMII port1 .. Done.


Detected DRAM size 256MB
Detect SysClk  320MHz
Detect Tclk    200MHz
Marvell Controller initialization Done.
Eth int Ctrl.... Done
GPIO int Ctrl... Done
PEX int Ctrl.... Done
PEX0 init....... Done. DEVICE type selected
USB Init........ Done
USB int Ctrl.... Done
XOR int Ctrl.... Done
XOR init........ Done
mvCtrlInit2..... done
PCI auto config. done
sysHwInit2...... DoneUSB2 Host Stack Initialized.
USB Hub Driver Initialized
USBD  Wind River Systems, Inc. 560 Initialized
Non-PCI USB device found: pgmIf=0xa0, idx=0 , baseAddr=0xf1050100, irq=19, swapFunc=0x10abf4
EHCI Controller found.
Waiting to attach to USBD...Done.
0xffffe50 (tRootTask): usbBulkDevInit() returned OK
usbCbiUfiDevInit() returned OK
CBI Class Driver Successfully Initialized
i2cInit:FAILURE: Channel Map not inited for modelId[0x0]

System Configuration

BSP Ver: 1.2/1.1.01   Creation date: Dec 28 2021, 06:34:22
CHIP   : MV88F6281 Rev 2
CPU    : ARM926 (Rev 1)
BOARD  : DB-98DX4122-48G (0x7)
CLOCKs : tClk =  200 MHz, sysClk =  320 MHz
         pClk =  800 MHz

NAT_SUPPORT         = Disabled
VFP_SUPPORT         = Disabled
Target Name: vxTarget
Attaching network interface lo0... done.
Write Protecting exception Vectors

 Write protecting KFos .text sections (0x100000 to 0x6d3000)  1491 pages

Adding 16789 symbols for standalone.


Boot parameters are:

flash(0,0)cmm:default e=10.4.50.165:ff000000 g=10.4.50.5 u=admin cb=9600 cp=none cs=1 cw=8 cm=modemControlOff


AOS kernel version: 6.7.2.160.R08
VxWorks (for DB-98DX4122-48G BE MMU ARCH 5) version VxWorks5.5.1
KERNEL: WIND version 2.6
Made on Dec 28 2021, 06:34:22.
Copyright Wind River Systems, Inc., 1984-2006

CPU: DB-98DX4122-48G BE MMU ARCH 5.  Processor #0.
Memory Size: 256 MBytes.  BSP version 1.2/1.1.01.

Portions of code copyrighted by Agranat Systems, Inc.  All Rights reserved
Portions of code copyrighted by ALE USA Inc., 2015. All Rights reserved
Portions of code copyrighted by Alcatel Internetworking, Inc. 1994-2014.  All Rights reserved
Portions of code copyrighted by Apptitude, Inc. 1997-1999.  All Rights reserved
Portions of code copyrighted by Free Software Foundation, Inc. 1989,1991.  All rights reserved
Portions of code copyrighted by The OpenLDAP Foundation 1999-2000.  All rights reserved
Portions of code copyrighted by Theodore T'so 1994,1995,1996,1997,1998,1999.  All Rights reserved
Portions of code copyrighted by RSA Security, Inc.  All Rights reserved
Portions of code copyrighted by Sun Microsystems, Inc.  All Rights reserved
Portions of code copyrighted by Wind River Systems, Inc.  All Rights reserved
Portions of code developed by the University of California, Berkeley.
Portions of code developed by the Carnegie-Mellon University.


sysInitializeTimezoneInfoInNvRam() failed.
RTC get failed ffff844

The current date and time is:
Coordinated Universal Time (UTC): FRI SEP 09 13:46:58 2095
Local time: FRI SEP 09 13:46:58 2095 UTC

sysGetModuleType CS EEPROM read FAILURE!!!
Starting dynamic software load from '/flash/certified/'...
Unable to read the EEPROM - ABORT !

In my case, I formated /flash via miniboot, re-transfer via zmodem (usb didnt work) and no changes.

[Gleylancer]

I'd think that the internal flash memory is most probably dead. It is not replaceable in a 6450. If your device is still in warranty or covered by a service plan, open a ticket with ALE.