Alcatel Unleashed

Hello all
i need a little help from you..

I have one remote customer with 4760 R5.2 installed ..
Now he is not able to access to 4760 at all..
It says " invalid password "

I tried to access through teamviewer and used toolsomnivista but with no use ..
Also i restarted the server ..

Is there any other solution you have to rescue us ??

and in case if we need to format the server,
can we install 4760 by using teaviewer ??

thank you very much
God bless you ..

Hi korin,

Kindly try using DirManag.exe located in \\4760\bin\ to reset your AdminNmc password.

1. Double-click DirManag.exe
2. Click Connect
3. Log-in as: cn=directory manager
4. Input the assigned password (default: AdminNmc)
5. Click OK button
6. After, expand o=directoryRoot\(company name)\Administration\Administrators\AdminNmc
7. On the right-window, find the parameter 'userpassword' and input a new password i.e. AdminNmc4760
8. After, select File\Save


Note: A notification will prompt stating creation was Successful! Click the OK button and try to log-in.

In addition, once you had a successful log-in, please remove or deactivate the aging password. Please take note that deactivating the aging password must be part of your post-configuration because it is activated by default in R5.2.



Thanks,
Zero

thank you zero very much
it is really helpful
i appreciate it

but in case if we need to install 4760 remotely .. can we install it by using teamviewer application ???

Hi korin,

Yes, apparently thru TeamViewer, you can install OmniVista 4760. However, please take not that it is not a recommended installation procedure.



Thanks & Regards,
Zero

Great information as it saved me from a rebuild, the ToolsOmniVista.exe would close after I put the default password. Luckily it worked with DirManag.exe to reset the adminnmc password to a new one.

Hello, I don't actually understand what should write in host, login and password.
Host is the ip server or name?.
Login: literally "cn=directory manager"?
Password:?

I've tried host: ip and name.
Port: ldap port
Login:" cn=directory manager" (without " ")
Password: AdminNmc, adminnmc, superuser...

And always get "Can't contact LDAP server"
"error connecting "

Hi Everyone,

I'm getting the next error: "Your login or password is not correct" when I'm trying to log in 4760 server.
If I use ToolOmnivista.exe, the application close immediatly when I put any password, even the default (adminnmc).
So, I tried to restore the password through DirManag.exe according the process in the previous posts, but always I get errors related with LDAP.
On the other hand, We have other server installed for the same OXE, this one was about to deactivate, I tried to connect with this server and I got the same error "Your login or password is not correct", but with this server I could accessed to ToolsOmnivista.exe, and I changed "supposedly" the adminnmc password, but I tried to log in and again I got the error.
I tried to change even the other passwords with ToolsOmnivista, but when I tried to change LDAP password I got "updating password failed: Not conneted to LDAP..."
Any suggestions?.

Dear KIKA,

If your server is running on Windows 7, you must execute toolsomnivista to "run as Administrator" whether via the command prompt or in \\4760\bin to eliminate immediate closure of the application's running process.

...I tried to restore the password through DirManag.exe according the process in the previous posts,...

Meanwhile, using the DirManage.exe, the process is to connect by putting ONLY the corresponding "Login" and "Password." For the "Login:" just type cn=directory manager while for "Password:" it is the installation password set then other parameters remained default or as is.



Regards,
Zero

Thank You [quote="Zero"][/quote].
I just read your answer.
Thank you for your guide, Even today, is very helpful

Zero wrote:Dear KIKA,
If your server is running on Windows 7, you must execute toolsomnivista to "run as Administrator" whether via the command prompt or in \\4760\bin to eliminate immediate closure of the application's running process.

Zero, i'm very grateful to you for advice. I could not understand because of what the problem. As a result, I was able to successfully perform the procedure "password reset"