Alcatel Unleashed

One more 6224 down,,please help me.


Boot1 Checksum Test...............................PASS

Boot2 Checksum Test...............................PASS

Flash Image Validation Test.......................PASS



BOOT Software Version 1.0.0.12 Built 19-Oct-2006 09:07:37

OS6200 board, based on PPC8247
128 MByte SDRAM. I-Cache 16 KB. D-Cache 16 KB. Cache Enabled.

Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
Decompressing SW from image-1
100%

OK
Running from RAM...

********************************************************************
*** Running SW Ver. 1.7.1.7 Date 12-May-2010 Time 16:32:04 ***
********************************************************************

HW version is 00.00.01
Base Mac address is: 00:12:cf:ae:65:a0
Dram size is : 128M bytes
Dram first block size is : 98304K bytes
Dram first PTR is : 0x2000000
Flash size is: 16M
01-Jan-2000 01:01:04 %CDB-I-LOADCONFIG: Loading running configuration.
01-Jan-2000 01:01:04 %CDB-I-LOADCONFIG: Loading startup configuration.
Device configuration:
CPLD revision: 1.00
PCB revision: R-0A
Slot 1 - OmniStack LS 6224P HW Rev. 1.0

------------------------------------
-- Unit Number 4 Slave --
------------------------------------

01-Jan-2000 01:01:17 %INIT-I-InitCompleted: Initialization task is completed


>PoE software version:
H.W. Version 0: Identifies the PCB version.
Full S.W. version is: Prod#.SW Ver.Param# - 0.505.4
Build Num 2, Internal SW 341.
The same version ...

PoE device version:
PoE Device 0, hw Version: 2. 12 ports.
PoE Device 1, hw Version: 2. 12 ports.

>
>?
Unknown parameter
May be one from the following list:

debug help

>debug
Enter DEBUG Password:
Bad Password
>

------------------------------------
-- Unit Number 4 Slave --
------------------------------------

- what is your concern sir? would you like your switch to be boot in normal?

- try to back read sir or search for 6224 stack
- or http://alcatelunleashed.com/viewtopic.p ... 224#p59212 and
http://alcatelunleashed.com/viewtopic.p ... 224#p64660

regards,

Vipin wrote:

BOOT Software Version 1.0.0.12 Built 19-Oct-2006 09:07:37

OS6200 board, based on PPC8247
128 MByte SDRAM. I-Cache 16 KB. D-Cache 16 KB. Cache Enabled.

OK
Running from RAM...

********************************************************************
*** Running SW Ver. 1.7.1.7 Date 12-May-2010 Time 16:32:04 ***
********************************************************************

HW version is 00.00.01
Base Mac address is: 00:12:cf:ae:65:a0
Dram size is : 128M bytes
Dram first block size is : 98304K bytes
Dram first PTR is : 0x2000000
Flash size is: 16M
01-Jan-2000 01:01:04 %CDB-I-LOADCONFIG: Loading running configuration.
01-Jan-2000 01:01:04 %CDB-I-LOADCONFIG: Loading startup configuration.
Device configuration:
CPLD revision: 1.00
PCB revision: R-0A
Slot 1 - OmniStack LS 6224P HW Rev. 1.0

------------------------------------
-- Unit Number 4 Slave --
------------------------------------

01-Jan-2000 01:01:17 %INIT-I-InitCompleted: Initialization task is completed

>

Shouldn't you have boot 1.0.0.13 if trying to run image 1.7.1.7?

Also this switch was stacked, please revert to factory setting s first.