ACT media gateway INTIPB

Rezakaa · Post by **Rezakaa** » 23 Jul 2010 15:59

Hi,

In an ACT Media Gateway with INTIPB what is the ethernet configuration?? (auto nego. half and full duplex, forced 100MB full duplex, etc). This parameter apear in a configuration of an INTIPA but not in an INTIPB. Does anybody knows?.Apparently this is causing a reset of the ACT media gateway, this is the incident that shows:

22/07/10 15:00:01 000000M|001/20/0/254|=2:0379=Inter ACT link HS: 23,(19,1),172.16.16.8,00:80:9f:8c:ee:e6

Or what can be happend, i hope you can help me.

Regards.

murraya · Post by **murraya** » 23 Jul 2010 19:14

you should be able to configure the sppee detc by the console port on the INTIPB Rezakaa.

Rezakaa · Post by **Rezakaa** » 24 Jul 2010 10:29

I will try and let you know. thanks Murray

Rezakaa · Post by **Rezakaa** » 03 Aug 2010 15:16

Murraya you were right I could change the speed of the ethernet conection through the console port, but the problem persists ACT is reset from time to time, the error is as follows "22/07/10 15:00:01 000000M|001/20/0/254|=2:0379=Inter ACT link HS: 23,(19,1),172.16.16.8,00:80:9f:8c:ee:e6", with incinfo shows:

INCIDENT NUMBER: 379
Network indicator: Alcatel 4400
OBJECT CLASS: Dhs3Terminal
EVENT TYPE: EquipmentAlarm (4)
PROBABLE CAUSE: Unknown (0)
SEVERITY: Major

"Inter ACT link HS: P1"
"P1 : Error type"
"P2 : IP Inter-crystal Link out of service"
"P3 : Internet address of INTIP_B"
"P4 : MAC Address of the INTIPB if possible"
"Inter-crystal signaling link problems on"
"link establishment or existant link shutdown"
"Several causes"
"Depend of the error value:"
" 0 Link out of service - IP Coupleur IP not initialized"
" 1 Link out of service - MAC Address already allowed"
.
.
" 23 Link out of service - No more signalling ressources"
" (There is no INTIPA in service)."
" 24 Link out of service - following INTIPA deletion"
"no reaction of the system."
"Check IP ressources boards within intipb."
"To see timer used tabtemp tool.";

I think it has something to do with the connection inter-ACT but not sure what to do, any ideas?

I hope you can help

leo · Post by **leo** » 03 Aug 2010 22:55

Hope the shelf address is correctly managed on INTIP board via DIP switch settings.

Rezakaa · Post by **Rezakaa** » 04 Aug 2010 08:41

yes it is leo, if would not be that way the ACT dont work, anyway i will check again. thanks if you have any idea let me know

btlasisi · Post by **btlasisi** » 04 Aug 2010 09:15

You may be having Speed/Duplex mismatch between your INTIPB 10baseT ethernet board and your switch port.

Rezakaa · Post by **Rezakaa** » 04 Aug 2010 09:50

btlasisi i already configure the speed of the ethernet board and thats not the problem, other idea? thanks

leo · Post by **leo** » 05 Aug 2010 01:25

Is there any INTOF connection with 4*64 kbps signaling being used ay ur site?

Rezakaa · Post by **Rezakaa** » 05 Aug 2010 08:08

No there is not, but there is a INTIPA connected i dont know if this is relevant for the case.