hello,
Thank you in advance to those who could help me
I had to remove a board E1 ISDN ,but i have already this error
Delete \OmniBRN\Shelf::5\Board::3
Board Address : Term. are connected to the board
i delete all term connected to this board by deletin all trunk and trunk group .
Can any one help me .
OXE break E1 ISDN
-
mokhtar ACFE
OXE break E1 ISDN
You do not have the required permissions to view the files attached to this post.
Re: OXE break E1 ISDN
what output do you have with command...
trkstat 5 3
regards...
trkstat 5 3
regards...
--- back to basics... focus your eyes to the essential things... ---
-
mokhtar ACFE
Re: OXE break E1 ISDN
thnk you , I have this output .
+------------------------------------------------------------------------------+
| T R U N K S T A T E - PRA T Coupler Crystal_nbr = 5 |
| OUT OF SERVICE Coupler Nbr = 3 |
+------------------------------------------------------------------------------+
| Access 0 Type : T2 access : ENABLED level2 : DCONNECT2 |
| |
| Trunk Grp |
| Channel 1 2 3 4 5 6 7 8 9 10 11 12 |
| State -- -- -- -- -- -- -- -- -- -- -- -- |
| |
| Trunk Grp |
| Channel 13 14 15 17 18 19 20 21 22 23 24 25 |
| State -- -- -- -- -- -- -- -- -- -- -- -- |
| |
| Trunk Grp |
| Channel 26 27 28 29 30 31 |
| State -- -- -- -- -- -- |
+------------------------------------------------------------------------------+
| F: Free | B: Busy | Ct: busy Comp trunk | Cl: busy Comp link |
| WB: Busy Without B Channel| Cr: busy Comp trunk for RLIO inter-ACT link |
| WBD: Data Transparency without chan.| WBM: Modem transparency without chan. |
| D: Data Transparency | M: Modem transparency |
+------------------------------------------------------------------------------+
| ALARM COUNTERS |
+------------------------------------------------------------------------------+
| NOS | AIS | LOS | FEC/CEC | RAI |
| 0 | 0 | 0 | 0 | 0 |
|------------------------------------------------------------------------------|
| NOS : no signal | LOS : loss of synchronization |
| AIS : alarm indication signal | FEC/CEC : Frame/Checksum error counter |
| RAI : remote alarm indication | |
+------------------------------------------------------------------------------+
+------------------------------------------------------------------------------+
| T R U N K S T A T E - PRA T Coupler Crystal_nbr = 5 |
| OUT OF SERVICE Coupler Nbr = 3 |
+------------------------------------------------------------------------------+
| Access 0 Type : T2 access : ENABLED level2 : DCONNECT2 |
| |
| Trunk Grp |
| Channel 1 2 3 4 5 6 7 8 9 10 11 12 |
| State -- -- -- -- -- -- -- -- -- -- -- -- |
| |
| Trunk Grp |
| Channel 13 14 15 17 18 19 20 21 22 23 24 25 |
| State -- -- -- -- -- -- -- -- -- -- -- -- |
| |
| Trunk Grp |
| Channel 26 27 28 29 30 31 |
| State -- -- -- -- -- -- |
+------------------------------------------------------------------------------+
| F: Free | B: Busy | Ct: busy Comp trunk | Cl: busy Comp link |
| WB: Busy Without B Channel| Cr: busy Comp trunk for RLIO inter-ACT link |
| WBD: Data Transparency without chan.| WBM: Modem transparency without chan. |
| D: Data Transparency | M: Modem transparency |
+------------------------------------------------------------------------------+
| ALARM COUNTERS |
+------------------------------------------------------------------------------+
| NOS | AIS | LOS | FEC/CEC | RAI |
| 0 | 0 | 0 | 0 | 0 |
|------------------------------------------------------------------------------|
| NOS : no signal | LOS : loss of synchronization |
| AIS : alarm indication signal | FEC/CEC : Frame/Checksum error counter |
| RAI : remote alarm indication | |
+------------------------------------------------------------------------------+
-
mokhtar ACFE
Re: OXE break E1 ISDN
Hi
the problem is solved, I changed the board by a new card E1 ISDN . Now i can delete all trunk group .
thanks
the problem is solved, I changed the board by a new card E1 ISDN . Now i can delete all trunk group .
thanks
Re: OXE break E1 ISDN
thx2 4 sharing
regards...
regards...
--- back to basics... focus your eyes to the essential things... ---
Re: OXE break E1 ISDN
Usually this happen - when we delete access but users use this TG. We cannot see access, but when we try to delete board or use access in another TG - PBX not allow this.
After PBX restart - access can be used/ board deleted. I use another solution - after some times - I delete access again (only via mgr) - delete the same access from the TG.
My opinion - when we delete access first time - access deleted from HDD database but not deleted from RAM database (access used). We cannot delete access from 4760 (access not present on HDD) but mgr allow to say - delete access X-XX-X from TG XXX
After PBX restart - access can be used/ board deleted. I use another solution - after some times - I delete access again (only via mgr) - delete the same access from the TG.
My opinion - when we delete access first time - access deleted from HDD database but not deleted from RAM database (access used). We cannot delete access from 4760 (access not present on HDD) but mgr allow to say - delete access X-XX-X from TG XXX
-
jainmanish94
- Member
- Posts: 8
- Joined: 20 Sep 2023 21:48
Re: OXE break E1 ISDN
Hello Team,
can anyone help me to tell what is the uses of ISDN Access - E1 PRA-T2 in OmniPCX Device.
there are two ports one is for PBX and another is for NETW and one my copper cable is connecting on NETW port which is going to PTN devices.
here i just want to know what is the exctual uses of this E1 Port.
can anyone help me to tell what is the uses of ISDN Access - E1 PRA-T2 in OmniPCX Device.
there are two ports one is for PBX and another is for NETW and one my copper cable is connecting on NETW port which is going to PTN devices.
here i just want to know what is the exctual uses of this E1 Port.
