Code: Select all
U-Boot 1.3.0-rc3 (Mar 5 2010 - 11:50:23) 3EH30350AAAM bootl100/000.012
Reset Status: Software Hard, External/Internal Soft, External/Internal Hard
CPU: e300c4, MPC8377, Rev: 21 at 666.666 MHz, CSB: 333 MHz
I2C: ready
DRAM:
DDR DIMM: data bus width is 64 bit without ECC
DDRC ECC mode: OFF
DDR RAM: 256 MB
FPGA: /soc@e0000000/gpio@c00/fpga@01f00000: FPGA4C1NV reloading... done
FLASH: 2 MB
PCI: Bus Dev VenId DevId Class Int
00 17 1064 2102 0000 00
00 18 1064 2102 0000 00
00 1d 10ee 0300 0b40 ff
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1
eSDHC: 4bit-buswidth mode
SATA: SATA0 [Link: no RDY]
SATA1 [Link: no RDY]
## Booting image at ff836de0 ...
Image Name: aleboot.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 8840 Bytes = 8.6 kB
Load Address: 00200000
Entry Point: 00201954
Verifying Checksum ... OK
OK
m41t11 Chip
No Prompt
Press ^B^I to enter into the Bios menu 0 Booting from SDMMC
Hit any key to stop autoboot: 0
## Booting image at ff8390a8 ...
Image Name: gpioinit.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 2185 Bytes = 2.1 kB
Load Address: 00200000
Entry Point: 00200620
Verifying Checksum ... OK
OK
Watchdog Started
898 bytes read
## Executing script at 00100000
1851658 bytes read
10177018 bytes read
## Booting image at 04000000 ...
Image Name: Linux-2.6.23.17-020.001
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1851594 Bytes = 1.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at 06000000 ...
Image Name: OXE_NGP_2.0_int
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 10176954 Bytes = 9.7 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ...
Requesting system reboot
Restarting system.
ÿ
U-Boot 1.3.0-rc3 (Mar 5 2010 - 11:50:23) 3EH30350AAAM bootl100/000.012
Reset Status: Software Hard, External/Internal Soft, External/Internal Hard
CPU: e300c4, MPC8377, Rev: 21 at 666.666 MHz, CSB: 333 MHz
I2C: ready
DRAM:
DDR DIMM: data bus width is 64 bit without ECC
DDRC ECC mode: OFF
DDR RAM: 256 MB
FPGA: /soc@e0000000/gpio@c00/fpga@01f00000: FPGA4C1NV reloading... done
FLASH: 2 MB
PCI: Bus Dev VenId DevId Class Int
00 17 1064 2102 0000 00
00 18 1064 2102 0000 00
00 1d 10ee 0300 0b40 ff
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1
eSDHC: 4bit-buswidth mode
SATA: SATA0 [Link: no RDY]
SATA1 [Link: no RDY]
## Booting image at ff836de0 ...
Image Name: aleboot.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 8840 Bytes = 8.6 kB
Load Address: 00200000
Entry Point: 00201954
Verifying Checksum ... OK
OK
m41t11 Chip
No Prompt
Press ^B^I to enter into the Bios menu 0 Booting from SDMMC
Hit any key to stop autoboot: 0
## Booting image at ff8390a8 ...
Image Name: gpioinit.bin
Image Type: PowerPC U-Boot Standalone Program (uncompressed)
Data Size: 2185 Bytes = 2.1 kB
Load Address: 00200000
Entry Point: 00200620
Verifying Checksum ... OK
OK
Watchdog Started
898 bytes read
## Executing script at 00100000
1851658 bytes read
10177018 bytes read
## Booting image at 04000000 ...
Image Name: Linux-2.6.23.17-020.001
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1851594 Bytes = 1.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at 06000000 ...
Image Name: OXE_NGP_2.0_int
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 10176954 Bytes = 9.7 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Booting using the fdt at 0x5800000
Loading Ramdisk to 0f5ea000, end 0ff9e9ba ... OK
Loading Device Tree to 007fd000, end 007fefff ... OK
setup_arch: bootmem
ale8377_intip3_setup_arch()
arch: exit
Using Alcatel-Lucent 8377 INTIP3 machine description
Linux version 2.6.23.17-020.001 (dri@frillux) (gcc version 4.1.2) #1 PREEMPT Thu Jul 16 11:07:18 CEST 2009
Found initrd at 0xcf5ea000:0xcff9e9ba
[MTD] Found 5 partitions in device-tree
Found MPC83xx PCI host bridge at 0x00000000e0008500. Firmware bus number: 0->0
Zone PFN ranges:
DMA 0 -> 65536
Normal 65536 -> 65536
HighMem 65536 -> 65536
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 65536
Built 1 zonelists in Zone order. Total pages: 65024
Kernel command line: root=/dev/ram console=ttyS0,9600 powersave=off boot_from=flash console_baudrate=9600 factory_mode=no
IPIC (128 IRQ sources) at fcff9700
PID hash table entries: 1024 (order: 10, 4096 bytes)
I-pipe 2.0-09: pipeline enabled.
console [kgdb0] enabled
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 245180k/262144k available (3684k kernel code, 16636k reserved, 156k data, 525k bss, 148k init)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Found MPC8377 (hardware revision 2.1)
Read ALE devices configuration from DeviceTree
NULL bootp pointer
PCI: Probing PCI hardware
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 9938k freed
prom_parse: Bad cell count for /soc@e0000000/mdio@24520/ethernet-phy@1
prom_parse: Bad cell count for /soc@e0000000/mdio@24520/ethernet-phy@2
Xenomai: system heap size: 16384 kB
I-pipe: Domain Xenomai registered.
Xenomai: hal/powerpc started.
Xenomai: init success
I-pipe: Domain IShield registered.
Xenomai: real-time nucleus v2.4.5 (Overdriver) loaded.
Xenomai: starting native API services.
Xenomai: starting POSIX services.
Xenomai: starting RTDM services.
Xenomai: starting RTAI emulator.
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0xe0004500 mem 0xd1002500 (irq = 20) is a 16550A
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0xe0004600 mem 0xd1004600 (irq = 21) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
Gianfar MII Bus: probed
eth0: Gianfar Ethernet Controller Version 1.3-skbr, 00:80:9f:8d:47:4e
GFAR: SKB Handler initialized at CPU#0(max=32)
eth0: MTU = 1500 (frame size=1526, truesize=1808)
eth0: Running with NAPI disabled
eth0: 1024/256 RX/TX BD ring size
eth1: Gianfar Ethernet Controller Version 1.3-skbr, 00:80:9f:8d:47:4f
GFAR: SKB Handler initialized at CPU#0(max=32)
eth1: MTU = 1500 (frame size=1526, truesize=1808)
eth1: Running with NAPI disabled
eth1: 1024/256 RX/TX BD ring size
kgdboe: couldn't parse config at not_configured!
kgdboe: configuration incorrect - kgdboe not loaded.
Usage: kgdboe=[src-port]@[src-ip]/[dev],[tgt-port]@<tgt-ip>/<tgt-macaddr>
physmap platform flash device: 00200000 at ff800000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 4 MTD partitions on "physmap-flash.0":
0x00000000-0x000e0000 : "firmware"
0x000e0000-0x00100000 : "hardware"
0x00110000-0x001f0000 : "fs"
0x001f0000-0x00200000 : "factory"
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 38, io base 0xe0023000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
esdhc: Freescale Enhanced Secure Digital Host Controller driver
esdhc:slot0: SDCard is Full-Speed Capable (25 MHz)
esdhc:slot0: Invalid maximum block size, assuming 512
mmc0: ESDHC at 0xe002e000 irq 42 DMA
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing unused kernel memory: 148k init
esdhc:slot0: SDCard clock is now running at 372023 Hz
esdhc:slot0: SDCard clock is now running at 23809523 Hz
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 STEC 249856KiB
mmcblk0: p1
loop: module loaded
Thu Jan 1 00:00:10 UTC 1970
[Script /etc/rc.d/rc.sysinit (PID=901) started by "init"]
[starti802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
ng cron]
crond[All bugs added by David S. Miller <davem@redhat.com>
1338]: crond 1.7.2 started, log level 8
[SetEthernet Channel Bonding Driver: v3.1.3 (June 13, 2007)
ting kernel/netwbonding: MII link monitoring set to 200 ms
ork/platform options]
[insertinbonding: bond0: Warning: failed to get speed and duplex from eth0, assumed to be 100Mb/sec and Full.
g kernel modulesbonding: bond0: making interface eth0 the new active one.
]
inserting 802bonding: bond0: first active interface up!
1q ()
insertingbonding: bond0: enslaving eth0 as an active interface with an up link.
bonding (mode=1bonding: bond0: Warning: failed to get speed and duplex from eth1, assumed to be 100Mb/sec and Full.
bonding: bond0: enslaving eth1 as a backup interface with an up link.
inserting x_tables ()
inserting ipt_ttl ()
inserting ipt_TTL ()
inserting ip_tables ()
ip_tables: (C) 2000-2006 Netfilter Core Team
inserting xt_NFLOG ()
inserting xt_NFQUEUE ()
Netfilter messages via NETLINK v0.30.
inserting nfnetlink_queue ()
inserting nfnetlink_log ()
inserting iptable_filter ()
inserting iptable_mangle ()
inserting iptable_raw ()
inserting xt_tcpudp ()
insertintun: Universal TUN/TAP device driver, 1.6
g xt_mark ()
intun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
serting xt_MARK bonding: bond0: link status definitely down for interface eth0, disabling it
bonding: bond0: making interface eth1 the new active one.
()
inserting tun ()
inserting alz-driver ()
Register platform Alcatel-Lucent 8377 INTIP3 specific functions
Invalid magic in bootp request
[wdt] Driver Initialization
cCPU Watchdog Timer not enabled (60 seconds, nowayout=0) tdelay=1000
bonding: bond0: link status definitely down for interface eth1, disabling it
bonding: bond0: now running without any active interface !
rtc model m41t11
m41t11 0-0068: rtc core: registered m41t11 as rtc0
[alz] Register alz_gpio...
[alz] Register Armada EEPROM drivers
Registered led device: CPUgreen
Registered led device: CPUred
Registered led device: CPUyellow
Registered led device: BSYyellow
[Restore system m41t11 0-0068: read: 49 24 d0 06 01 03 13
m41t11 0-0068: read secs=49, mins=24, hours=10, mday=1, mon=2, year=113, wday=5
Fri Mar 1 10:24:49 UTC 2013
[starting background processes]
[starting syslogd]
[Lock reset management to kernel module]
[start loopback device]
[starting network]
[Check Storage device]
[Check SDcard partition]
[Try to mount SDkjournald starting. Commit interval 5 seconds
EXT3 FS on mmcblk0p1,
internal journal
EXT3-fs: mounted filesystem with ordered data mode.
[SDcard partition OK]
[BOOT directory to be updated]
End of platform init
[Wait for 5m before rotating log to keep header]
Fri Mar 1 10:24:50 UTC 2013
[Script /etc/rc.d/rc (PID=1505) started by "init"]
=== BIENVENUE TO INTIP 3 Software v. 04.03 in INTIP3 board / intip3 mode / INTIPB role ===
=== Kernel version : 2.6.23.17-020.001 ===
***** SDcard owner = intip3 ***** Board = intip3 *****
[Retrieve IPMG configuration]
/mnt/flash/local/ipmg.cfg: OK
Find ipmg.cfg configuration file in /mnt/flash/local
/mnt/flash/local/startup.cfg: OK
Find startup.cfg configuration file in /mnt/flash/local
/mnt/flash/local/pcs.cfg: OK
Find pcs.cfg configuration file in /mnt/flash/local
Reading of configuration in flash finished
No password file found - using default password list
PHY: e0024520:01 - Link is Up - 1000/Full
bonding: bond0: link status definitely up for interface eth0.
bonding: bond0: making interface eth0 the new active one.
bonding: bond0: first active interface up!
Duplex mode set to 1 BUT forced to auto-negociation mode
Starting /etc/rc.d/rcS/01pipe
Starting /etc/rc.d/rcS/10network
Setting hostname....
[Start mod_incid
INCIDENT_DEVICE :: INCIDENT driver registered to Linux
.ko]
[Start net_restart]
bonding: bond0: Warning: the permanent HWaddr of eth0 - 00:80:9F:8D:47:4E - is still in use by bond0. Set the HWaddr of eth0 to a different address to avoid conflicts.
bonding: bond0: releasing active interface eth0
bonding: bond0: releasing backup interface eth1
bonding: bond0: making interface eth0 the new active one.
bonding: bond0: first active interface up!
bonding: bond0: enslaving eth0 as an active interface with an up link.
bonding: bond0: enslaving eth1 as a backup interface with a down link.
Bringing up interface bond0 ....
Detected current net interface : eth0
bonding: bond0: link status definitely down for interface eth0, disabling it
bonding: bond0: now running without any active interface !
[Checking duplicated IP addr 10.10.160.12 through bond0]
PHY: e0024520:01 - Link is Up - 1000/Full
bonding: bond0: link status definitely up for interface eth0.
bonding: bond0: making interface eth0 the new active one.
bonding: bond0: first active interface up!
[ IP addr checked and DOES NOT appear duplicated ]
IPv4 packet forwarding is enabled....
IPv4 automatic defragmentation is disabled....
IPv4 TCP timestamps is disabled....
Starting /etc/rc.d/rcS/90init
Uboot updater is now working ... getting current version information
Check if we need to update with Uboot bootl100/000.012 ...
Current version : bootl100/000.012 / Recorded version : bootl100/000.012
..... Uboot update not needed .....
[Warning] Net status : yes at 1000Mb/s
[Warning] Call lanpbx_mngt
Authentification lanpbx FAILED --> see /var/log/lanpbx_mngt
LANPBX.CFG contents :
-> TYPE=A4400 VERSION=1 IP_DOWNLOAD=10.10.160.3 IP_CPU1=10.10.160.2 IP_CPU2=10.10.160.1
[Start build_hosts 0]
start of load appli modules phase
Loading modules - please wait ...
[Start RT2LxCMD]
[Start xeno_bkRegistering Adeos/Xenomai Backtrace
t.ko]
[xeno_bkt]: Albator pid is 1470
[Start xeno_ipmgxeno_ipmg_drv: module license 'Alcatel-Lucent' taints kernel.
_drv.ko]
ipmg_drv module loaded
/proc/IPMG proc entry created
[Start inox_hpi.ko & inox_pci.ko common interfacInox_pci found 0 Dsps
e]
Inox_pci found 2 Dsps
[Start dbg_mngr.ko and fw_mngr.ko telecom DSPs lModule rt_printf loaded
ow level managemStarting monitor using pipe 1
ent]
[Start xenUUo_printf.ko]
[Start xeno_monitor.ko]
binamcvb642x AUTHENTICATION OK
[Start amcvd.ko common interface]
nbInox:2 dspInfos.InoxId:1 dspInfos.Pos:0 inoxTelId:0 => dspId:0
nbInox:2 dspInfos.InoxId:1 dspInfos.Pos:1 inoxTelId:0 => dspId:1
DSPWare Version : AMCVB / 2.20 / Checksum 04ef7d03
[Start adiat_driCreate /proc/adiat
ver.ko common inAdiat driver module loaded
terface]
[Start xeno_mem_/proc/IPMG/DMAMemoryManager proc entry created
mgr.ko]
rt_mem_mgr : General Heap for Real Time : 16777216 bytes
DMA memory allcator initialized : 20 chunks of 131072 bytes
Real-Time Linux Dynamic Memory Manager
[Start xeno_syscxeno_syscall : module loaded.
all.ko]
[Start xeno_syscall_agent]
[Start xeno_ca_kernel.ko]
Application specification : intip3
Alcatel-Lucent kernel module loading...
---------------- Rings Init : Begin ---------------
ca_kernel : Creating Heap Tx [ OK ]
ca_kernel : Allocating Heap Tx [512] [ OK ]
ca_kernel : Creating Heap Rx [ OK ]
ca_kernel : Allocating Heap Rx [512] [ OK ]
---------------- Rings Init : End -----------------
fastsk : Shared heap allocated
Module Kernel Loaded
[Start Socket Agent]
[Start c1nv_mngt.ko]
[Use of /mnt/flash/local/tonesnv]
pci_get_device cffe9000
pci_enable_device 0
pci_request_region 2 0
ioremap 2 d3a00000
pci_request_region 1 0
ioremap 1 d3a80000
pci_request_region 0 0
ioremap 0 fcffe400
[PowerOff] (IRQ #0 (0) received).
irq = 18
request_firmware BNVINTIP 0 d22f2fd8
request_firmware TONES 0 d22f3128
[Start intip_mngt.ko]
SoftMSM_Sig = 0
Fri Mar 1 10:25:26 UTC 2013
[Script /etc/rc.shutdown (PID=1861) started by "init"]
Script Log disabled
[Notify RT application to engage shutdown]
ca_kernel : Fast Socket Initialization.
ca_kernel : no param_8021q=-1 is used
ca_kernel : no vlan set
Module INTIP Loaded
[Start c1nv_procDirectory /mnt/flash/info/c1nv OK
.ko]
/mnt/flash/info/c1nv/c1nvnorst doesn't exist -1
Next idx_hist: 2
[Start srtp_module.ko]
SRTP Module is loaded but security is not implemented in this release
[Start ca_media_server.ko]
[Notify RT application to halt now]
[Backup system tm41t11 0-0068: write secs=29, mins=25, hours=10, mday=1, mon=2, year=113, wday=5
ime to RTC]
m41t11 0-0068: write 29 25 d0 06 01 03 13
Fri Mar 1 10:25:30 UTC 2013
[Script /etc/rc.d/init.d/save_info (PID=1883) started by "/etc/rc.shutdown"]
[No backtrace]
[No new core dump]
[Saving logs]
[Stopping swap]
[Lazy Unmounting everything]
media Module is loading (setcomphs=0)...
media Module version Feb 8 2012-15:45:53
media Module Author Written by ALE ...
Starting Load of media server module
End of update_obj_tb phase
End of determine_offset phase : 9 objects passed
Start of allocators construction phase (static)
init module media_server : after allocation of VoIP context objects pools
[Stopping network]
[End of rc.shutdown]
The system is going down End of loop on channels from 0 to 128
NOW!
Sending SBefore special objects treatment : RTCP RR and fastsk for RTCP and T38 objects
IGTERM to all prEnd of link on fastsk objects for RTCP_RR : inst numbers from 128 to 255
ocesses
SyscallEnd of link on fastsk objects for RTCP_SR : inst numbers from 256 to 383
Agent[1827]: SigEnd of link on fastsk objects for udptl : inst numbers from 384 to 511
nal 15 catched -fastsk objects srtp for Thales box : inst number 512
-> shutdown!!!
fastsk objects fax for Thales box : inst number 513
SyscallAgent[Module media_server loaded
1827]: rt_syscalmedia server module is loaded
l0 closed
xeno_syscall_agent[1827]: End
Sending SIGKILL to all processes
Requesting system reboot
