4059MAC + BLF

Post Reply
User avatar
OXO-Man
Member
Posts: 101
Joined: 02 Jan 2007 04:48
Location: Germany

4059MAC + BLF

Post by OXO-Man »

Hello Alcatel-Guru´s,

I´ve got a question concerning the 4059 MAC and the BLF:
Is it possible to run the 4059 MAC and the BLF on different PC´s? Our costumer want´s to use to different PC´s so he can use one only for the 4059 MAC-Attendant and the other (on the same desk) to see who´s in conversation and who´s free...

If yes: How can I connect the BLF to the OXE (cause the MAC-Box has only one serial port....)?

The system is an OXE R7.1, the version of 4059 is 4.016.9.

Sorry for my (perhaps) silly question but I never sold or installed the BLF before (only the 4059 MAC.... and I can´t find any doc´s about the installation of the BLF on the BPWS (including the TC0910...)

Thank you for your help!!!

Best regards
OXO-Man
ACSE OXO R8.0
ACSR OXO
ACSR Eye-Box
ACSE OXE R9.1
.. and a lot of more...!
torrentula

Re: 4059MAC + BLF

Post by torrentula »

I'm not sure if it can run on another pc, not that I'm aware of, maybe someone else has experience. What I have done in the past, is put in dual monitors on 1 pc and run the BLF on the second monitor, much cheaper than an entire second pc.
User avatar
OXO-Man
Member
Posts: 101
Joined: 02 Jan 2007 04:48
Location: Germany

Re: 4059MAC + BLF

Post by OXO-Man »

Hello torrentula,

I found out something:
It works on a second PC. I have to connect this PC to a V24-Port on the OXO.

But here is my problem: Do I have to use the MOXA-Box (on Common-Hardware) or can I use the V24-Port on the CS?
Which V24-application must I configure in mgr (I think: attendant supervision)?

Thank you for your answers...

OXO-Man
ACSE OXO R8.0
ACSR OXO
ACSR Eye-Box
ACSE OXE R9.1
.. and a lot of more...!
torrentula

Re: 4059MAC + BLF

Post by torrentula »

Like I said, I have no experience with using a second pc. But, I don't think I would use the V24 on the CS even if you can. What if you need console access? I would use a moxa box.
knightr1der

Re: 4059MAC + BLF

Post by knightr1der »

OXO-Man - you confuse me. In your first post you say you have OXE R7.1

After superb advice by Torrentula, you then post again and say it works on V24 of OXO.

These are 2 completely different systems. Are you asking that 'because it is possible on OXO, you now want to know if the same is possible on OXE'?

Pls don't misread my post - I am not reprimanding you (even though most of my message sounds like I am) - I am genuinely confused :?

Either way, why waste resources? Dual monitor is perfect solution, no?
User avatar
OXO-Man
Member
Posts: 101
Joined: 02 Jan 2007 04:48
Location: Germany

Re: 4059MAC + BLF

Post by OXO-Man »

Sorry knightr1der,

of course I mean the OXE (Enterprise). I don´t want to confuse you....

It was my fault with the OXO... normaly I´m working with the OXO and not with the OXE. So my fingers are typing OXO on my keyboard instead of OXE (Enterprise..)...

Concerning my problem:
I would use the MOXA-Box...

Many thanks for your help!!! (and hope you´ll helps me again in the future...... :-) )
Best regards
OXO-Man
ACSE OXO R8.0
ACSR OXO
ACSR Eye-Box
ACSE OXE R9.1
.. and a lot of more...!
Post Reply

Return to “Attendant”