I have a 7210 SAS-D that will not complete its boot cycle. It powers up, and I am able to console in. No matter what changes I make the switch just keeps looping through this process. I did notice there is a message saying the EEProm is not valid and I was wondering if I just have a bad switch or if I am missing something.
Alcatel-Lucent 7210 Boot ROM. Copyright 2009-2012 Alcatel-Lucent.
All rights reserved. All use is subject to applicable license agreements.
Testing ROM load area...done
Relocating code...Jumping to RAM
Performing second stage RAM test....passed
*** Card EEProm is not valid
Bootlog started for Version C-V-5.0.R2
Build V-5.0.R2 bootrom/mpc 7xxx
Built on Thu Dec 20 21:20:31 IST 2012 by builder in /home/builder/5.0B1/R2/panos/main
?Attempting to load from file cf1:/boot.tim
Version L-7.0.R5, Mon Apr 20 14:09:58 IST 2015 by builder in /home/builder/7.0B1/R5/panos/main
text:(5347008-->18339572) + data:(1039104-->5262104)
Starting at 0xb000000...
PCIe: Port 0 Link UP
Total Memory: 512MB Chassis Type: sas Card Type: badami_7210
TiMOS-L-7.0.R5 boot/mpc ALCATEL SAS-D 6F4T 7210 Copyright (c) 2000-2015 Alcatel-Lucent.
All rights reserved. All use subject to applicable license agreements.
Built on Mon Apr 20 14:09:58 IST 2015 by builder in /home/builder/7.0B1/R5/panos/main
TiMOS BOOT LOADER
readRtc returned error
Switching serial output to sync mode... done
Looking for cf1:/bof.cfg ... OK, reading
Contents of Boot Options File on cf1:
primary-image cf1:\7.0R5\both.tim
primary-config cf1:\new.cfg
#uplinkA Port Settings:
uplinkA-port 1/1/1
uplinkA-autoneg
uplinkA-duplex full
uplinkA-speed 1000
uplinkA-address 0
uplinkA-vlan 0
#uplinkB Port Settings:
uplinkB-port 1/1/2
uplinkB-autoneg
uplinkB-duplex full
uplinkB-speed 1000
uplinkB-address 0
uplinkB-vlan 0
#System Settings:
wait 3
persist on
console-speed 115200
no console-disabled
Hit a key within 1 second to change boot parameters...
Configuring Network with uplinkA Port Setting.....
Primary config file present at: cf1:\new.cfg
Index file present at: cf1:\new.ndx
Sap Index file present at: cf1:\new.sdx
Primary image location: cf1:\7.0R5\both.tim
Loading image cf1:\7.0R5\both.tim
Version B-7.0.R5, Mon Apr 20 14:11:07 IST 2015 by builder in /home/builder/7.0B1/R5/panos/main
text:(36273888-->131545080) + data:(4630752-->21719220)
Executing TiMOS image at 0x100000
Total Memory: 512MB Chassis Type: sas Card Type: badami_7210
TiMOS-B-7.0.R5 both/mpc ALCATEL SAS-D 6F4T 7210 Copyright (c) 2000-2015 Alcatel-Lucent.
All rights reserved. All use subject to applicable license agreements.
Built on Mon Apr 20 14:11:07 IST 2015 by builder in /home/builder/7.0B1/R5/panos/main
___ ___ ___ ___
/\ \ /\__\ /\ \ /\ \
\:\ \ ___ /::| | /::\ \ /::\ \
\:\ \ /\__\ /:|:| | /:/\:\ \ /:/\:\ \
/::\ \ _\/__/ /:/|:|__|__ /:/ \:\ \ _\:\~\:\ \
/:/\:\__\ /\__\ /:/ |::::\__\ /:/__/ \:\__\ /\ \:\ \:\__\
/:/ \/__/ /:/ / \/__/~~/:/ / \:\ \ /:/ / \:\ \:\ \/__/
/:/ / /:/ / /:/ / \:\ /:/ / \:\ \:\__\
\/__/ \/__/ /:/ / \:\/:/ / \:\/:/ /
/:/ / \::/ / \::/ /
\/__/ \/__/ \/__/
Card eeprom invalid
Resetting...OK