Problem between oxe and mitel pbx

[edylor2580]

Good night, everybody, my problem is that I have a link between oxe and mitel pbx (ISDN), it works fine I can call between them, but I have my PSTN external lines (analogs) in the OXE, but I want to use those lines from the mitel 3300, and I can´t; a t3 command said:
| (483292:000012) Physical-Event :
| long: 87 desti: 0 source: 0 cryst: 0 cpl: 9 us: 0 term: 0 type a5
| tei: 0 >>>> message received : SETUP [05] Call ref : 00 38
| SENDING COMPLETE
|______________________________________________________________________________
|
| IE:[04] BEARER_CAPABILITY (l=3) 80 90 a3
| IE:[18] CHANNEL (l=3) a9 83 9f -> T2 : B channel 31 exclusive
| IE:[1c] FACILITY (l=35)
| [91] Discriminator of supplementary service applications
| [aa] NFE (l=6):
| [80] Source Entity (l=1) End_PTNX
| [82] Destination Entity (l=1) End_PTNX
| [8b] Interpretation APDU (l=1): DISCARD (0)
| [a1] INVOKE (l=21):
| Invoke Ident. : 005b (91)
| OP: ECMA RO_CALLING_NAME (0)
| [30] Sequence (l=10)
| [80] Name presentation allowed (l=8) '1.bodega'
| [80] Context specific (l=8)
| IE:[6c] CALLING_NUMBER (l=6) -> 09 80 Num : 3011
| IE:[70] CALLED_NUMBER (l=7) -> 80 Num : 520026
| IE:[7d] HLC (l=2) 91 81
|______________________________________________________________________________

______________________________________________________________________________
| (483292:000014) 1886: Send_IO1 (link-nbr=9, sapi=0, tei=0) :
| long: 26 desti: 0 source: 15 cryst: 0 cpl: 9 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : STATUS [7d] Call ref : 80 38
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=3) 80 e3 1c -> [e3]
| INFORMATION ELEMENT NON-EXISTENT OR NOT IMPLEMENTED
| IE:[14] CALL_STATE (l=1) 06
|______________________________________________________________________________

______________________________________________________________________________
| (483292:000015) 1886: Send_IO1 (link-nbr=9, sapi=0, tei=0) :
| long: 22 desti: 0 source: 15 cryst: 0 cpl: 9 us: 8 term: 0 type a5
| tei: 0 <<<< message sent : REL COMP [5a] Call ref : 80 38
|______________________________________________________________________________
|
| IE:[08] CAUSE (l=2) 80 82 -> [82] NO ROUTE TO SPECIFIED TRANSIT NETWORK
|______________________________________________________________________________

the number 3011 is the extension calling, 5200 is the prefix to take the trunk and 26 is the extension.
I have seen some people solved this problem, can you help me with this .
Thank you

[haroun]

IS IT TRANSIT allowed
e1 trunkgroup PNC =?
isdn trunk connection cos =5 shhould be authorised to connect with pstn analog trunk C onnetion cos (see this under connection class of service)

[vad]

And DID transcoding for incoming TG.

[oldboy]

So if you dial 520026 from another extn on the OXE does it reach the destination??

[haroun]

by the way, stronge called number under pstn
you external pstn line witch mean public network and you call 26 as extension , is it Abbreviated number ?
public networks allow for regular subscriber at least 6 digits AB MCDU -for some country if you'r in same area and carrie you can use 4 digit-

[edylor2580]

Thanks everybody, I solved the problem like another people had done, I created TG 0 and added trunk lines, then I created a prefix 0 to adquire TG 0 in OXE, then in Mitel i created prefix 0 to get the TG 0 from OXE, and it worked.
Thanks.

[Dav1d]

Do you hava documentation how to make a (SIP Trunk) link between oxe and mitel pbx (3300 CX)?

[haroun]

Hi
at this moment , i Don't think there's an IWR for that scenario, but u can setuo it as a standard sip trunking solution
do you have necessary licenes ?
see system doc for configuration model (private or public sip trunking)

[Dav1d]

Hi
at this moment , i Don't think there's an IWR for that scenario, but u can setuo it as a standard sip trunking solution
do you have necessary licenes ?
see system doc for configuration model (private or public sip trunking)

Thanks for your awnser.
I have the necessary licences.
I will have a look into the configuration files for the Mitel 3300 CX and the Alcatel OXO

[haroun]

Your Alcatel box is OXO or OXE ?
if it's an Oxe give it a try (config and so on ) and if u need help do not hesitate by creating a new topic
just follow system doc oxe Rx /ip/sip/siptrunckin it should not be a big deal