Switch over of CS

[BANNAIRE]

Hello all

My problem :

OXE R9.1 two gateways, redundancy on, both call servers on the same subnetwork

When the CPUA is main, if I shutdown the CPUA, the switch over is OK, CPUB goes main and CPUA goes standby after reboot
When the CPUB is main, if I shutdown the CPUB, the CPUA reboots also (something like a broadcast message)

This is the netadmin configuration of both CPU. Did I do anything wrong ?
Thanks

CPUA
Your system has the private network number 0 and the site number 4.
Private IP addressing space: no
Restricted internet accesses: no
Accept ICMP redirect: no
Low dynamic ports range configuration : 10000 - 10499

There is no VLan configuration. No frame will be 802.1q-tagged.
The ethernet redundancy is not supported on this CPU type
node name : noeud4
internal name resolver activated : no


Ethernet interface setup
========================

Netmask : 255.255.255.0

==============================================================================
| Machine type | Local interface | Name | Address |
==============================================================================
| local | Ethernet | oxer9a | 192.168.0.70 |
| local main | Ethernet | main_oxe | 192.168.0.14 |
| local | IP/X25 tunnel | x000004_tun | 172.30.253.4 |
==============================================================================


<return> to continue.

CPU redundancy setup
====================

Netmask : 255.255.255.0

==============================================================================
| Machine type | Local interface | Name | Address |
==============================================================================
| local | Ethernet | oxer9b | 192.168.0.71 |
| local main | Ethernet | main_oxe | 192.168.0.14 |
==============================================================================

CPUB

Your system has the private network number 0 and the site number 4.
Private IP addressing space: no
Restricted internet accesses: no
Accept ICMP redirect: no
Low dynamic ports range configuration : 10000 - 10499

There is no VLan configuration. No frame will be 802.1q-tagged.
The ethernet redundancy is not supported on this CPU type
node name : noeud4
internal name resolver activated : no


Ethernet interface setup
========================

Netmask : 255.255.255.0

==============================================================================
| Machine type | Local interface | Name | Address |
==============================================================================
| local | Ethernet | oxer9b | 192.168.0.71 |
| local main | Ethernet | main_oxe | 192.168.0.14 |
| local | IP/X25 tunnel | x000004_tun | 172.30.253.4 |
==============================================================================


<return> to continue.

CPU redundancy setup
====================

Netmask : 255.255.255.0

==============================================================================
| Machine type | Local interface | Name | Address |
==============================================================================
| local | Ethernet | oxer9a | 192.168.0.70 |
| local main | Ethernet | main_oxe | 192.168.0.14 |
==============================================================================

Role adressing on both CPU

==============================================================================
| Machine type | Local interface | Name | Address |
==============================================================================
| local main | Ethernet | main_oxe | 192.168.0.14 |
| twin main | Ethernet | main_oxe | 192.168.0.14 |
==============================================================================

[smileyman]

He Bannaire,

what ist your patch-level? - In Release 9.1 with a low patch-level is a bug.

Best regards
smileyman

[BANNAIRE]

He

The relaese is I1 605.21. But this release works perfectly on other sites

Regards

[smileyman]

Hi Bannaire,
you are right. - I mean this: crms00256662 (dup of crms00255559): Stand-By CPU freezed after bascul (following a translation from Release 7.1.
But this is not your problem, i think.

Is 'twin' ok?

Best regards
smileyman

[BANNAIRE]

Hi

Yes, twin is OK on both CPU

Regards

[RobertBreu]

Hi,

what happens if you do a bascul?

[BANNAIRE]

Hi
The standby CPU goes main and reboots after a few seconds. So both CPU reboots
There is a message like this on the CPU which goes main

Broadcast message from root Sun Sep 11 19:21:50 2011...

The system is going down for reboot NOW !!


Regards

[smileyman]

Hi Bannaire,

please provide a incvisu from both CPUs. - I hope to see more.

Best regards

smileyman

[BANNAIRE]

Hi

Here incvisu of both CPU. At one moment, just after the Bascul, there are two call servers main. This is the reason, what do you think ?

Regards

[RobertBreu]

Hi,

do you have configured a reference media-gateway and/or a preferred main com server?