Search found 46 matches
- 24 Jul 2019 08:15
- Forum: Beginner's questions about the OmniPCX OFFICE
- Topic: IP Touch 4018 can't receive external call
- Replies: 2
- Views: 2288
Re: IP Touch 4018 can't receive external call
Hi Razor, Did you check the incoming call routing? > connect through the OMC (OmniPCX Office Management Console) > go to 'Numbering' > go to 'Numbering Plans' > go to the tab 'Public Numbering Plan' > Check if your colleague's number is in it. So ther should be a line or a range (from start to end) ...
- 23 Jul 2019 06:14
- Forum: GENERAL
- Topic: OmniPCX Office
- Replies: 3
- Views: 2495
Re: OmniPCX Office
Hi, > Connect to the PBX with your OMC > Go to: Subscribers/Basestations List > Click on 'Add' (the first tab on the right) > Choose 'IP Terminal' and choose an internal number, also fill in the name of the new extension and click on OK > Go in the Subscribers/Basestations List and change the type o...
- 23 Jul 2019 06:00
- Forum: Configuration
- Topic: OXO CONNECT R3.1 No authentication
- Replies: 1
- Views: 1961
Re: OXO CONNECT R3.1 No authentication
Hi Franck,
Can you show us the header of the SIP invite please? This piece of the trace doesn't show enough information.
Thanks.
Can you show us the header of the SIP invite please? This piece of the trace doesn't show enough information.
Thanks.
- 15 Jul 2019 08:06
- Forum: DECT
- Topic: Mobile 300 set on OXO Connect 3.1?
- Replies: 3
- Views: 7033
Re: Mobile 300 set on OXO Connect 3.1?
Hi Alex, We also encountered this issue and couldn't reinitialize the old phones on our OXO Connect 3.1 either. I tried to configure them in our labo system as a 3th party GAP device, but the PBX still seems to recognize them, preventing them from popping up in the DECT activation tool... You should...
- 03 Jul 2019 07:44
- Forum: Beginner's questions about the OmniPCX OFFICE
- Topic: TELNET access to Alcatel-Lucent OmniPCX Office systems
- Replies: 1
- Views: 3222
Re: TELNET access to Alcatel-Lucent OmniPCX Office systems
Hi G-Hart, You can login the OXO using telnet: - user: ftp_nmc - PW: tuxalize However, this won't solve your issue. In order to connect to a 3th party PMS and use it fully, you need the following things: 1. You need to put the ALE OXO in 'hotel mode' (in order to recieve/set room status through the ...
- 03 Jul 2019 07:15
- Forum: MAIN
- Topic: PM5 Expert
- Replies: 13
- Views: 13052
Re: PM5 Expert
Hi FrancoYanez,
I can provide you PM5_410_22_1a or PM5_310_25_1 if you want to, just PM me.
Grts,
Koen
I can provide you PM5_410_22_1a or PM5_310_25_1 if you want to, just PM me.
Grts,
Koen
- 21 Jun 2019 05:24
- Forum: MAIN
- Topic: SiP Trunk DID
- Replies: 3
- Views: 2410
Re: SiP Trunk DID
Hi DBasilio, You have to check two things for starters: 1. Can the OXO reroute the external number to the Cisco when the OXO sets up the call (can you do CLIPspoofing) - OMC > System Miscellaneous > Feature Design > Part 3 - Put the 'external diversion mode' from joining (by default) in Re-routing -...
- 17 Jun 2019 07:13
- Forum: Beginner's questions about the OmniPCX OFFICE
- Topic: Alcatel OmniPCX office small; outgoing calls not possible
- Replies: 6
- Views: 4655
Re: Alcatel OmniPCX office small; outgoing calls not possible
Hi TheHermann, CLIP no Screening is only possible if your telephony service provider allows it. Often they refer to this feature as 'CLIP SPOOFING'... If they allow it, you can try to configure it as below: For activating CLIP no Screening you can put the PBX in 'rerouting' - OMC > System Miscellane...
- 11 Jun 2019 06:12
- Forum: Beginner's questions about the OmniPCX OFFICE
- Topic: Alcatel OmniPCX office small; outgoing calls not possible
- Replies: 6
- Views: 4655
Re: Alcatel OmniPCX office small; outgoing calls not possible
Hi, Did you trace it out? Use the ISDN trace in the PBX to check what numbers you send to your Fritzbox. Sometimes, if the timers are not set correctly, the PBX sends the numbers too early (even before you finished dialling) So you should check if you use your 'End of dialing table' (if not, try it)...
- 21 May 2019 05:15
- Forum: Beginner's questions about the OmniPCX OFFICE
- Topic: OmniPCX Office - Console cable question
- Replies: 15
- Views: 8311
Re: OmniPCX Office - Console cable question
Hi, There's really no need to have an old serial cable. Even if you would put your PBX 'cold' and even if it loses it's IP adress, you can always find out the new IP by connecting the PBX's LAN port to a mirror switch. Let the PBX boot, and it will broadcast its IP adress. Then put your PC's NIC in ...