Search found 14 matches
- 12 Jul 2017 14:07
- Forum: Misc
- Topic: OmniStack 8008 password unknown help
- Replies: 0
- Views: 4291
OmniStack 8008 password unknown help
I have 3 OmniStack 8008's that has been setting on the shelf for allot longer than I have been with my company and no one knows what the login information for these units are. Factory resetting the units is fine since I do not need to keep the current config on them since we are selling them. I open...
- 05 Feb 2016 18:23
- Forum: AUDIOCODES
- Topic: Mediant 8000 media gateway factory reset help
- Replies: 5
- Views: 6344
Re: Mediant 8000 media gateway factory reset help
I use the serial port on the processor's back card. As for any manuals I have none, sorry.
- 09 Jul 2015 15:43
- Forum: AUDIOCODES
- Topic: can't get Mediant 8000 card tp-6310-t3 to load
- Replies: 0
- Views: 3640
can't get Mediant 8000 card tp-6310-t3 to load
I preform the following command to unlock the card after I add it but the card will not load the software and come up. "unlock /moGW/moBoard#11" (Also when I run this command I don't receive any output saying that it has been unlocked like what the manual says should show) when I look at t...
- 08 Jul 2015 19:04
- Forum: AUDIOCODES
- Topic: Mediant 8000 media gateway factory reset help
- Replies: 5
- Views: 6344
Re: Mediant 8000 media gateway factory reset help
I found the procedure on how to reset the root account see below. 1. Connect to the CLI interface on the specific SC board via RS-232 serial console. For more information, refer to 'Connecting to the CLI via RS-232 Serial Console' on page 73 2. Drop SC board to the OBP level (ok> prompt) by pressing...
- 08 Jul 2015 14:18
- Forum: AUDIOCODES
- Topic: Mediant 8000 media gateway factory reset help
- Replies: 5
- Views: 6344
Re: Mediant 8000 media gateway factory reset help
OK I was able to log into the active card with account of ems and password of ems, but now I can't seem to be able to run any of the show commands. I just get the following message
"can't connect to the CLI server"
"can't connect to the CLI server"
- 08 Jul 2015 13:49
- Forum: AUDIOCODES
- Topic: Mediant 8000 media gateway factory reset help
- Replies: 5
- Views: 6344
Mediant 8000 media gateway factory reset help
I have an AudioCodes Mediant 8000 media gateway with two PMC233 cards, with no clue what the active card password information is. I can log into the standby card with the cli account with the default password of cli, however I can not log into the active card with the cli account. I have restored Au...
- 06 Nov 2014 13:24
- Forum: 7750 SR
- Topic: 7750-SR message "Do not know what chassis type this is!"
- Replies: 2
- Views: 2481
Re: 7750-SR message "Do not know what chassis type this is!"
unfortunately their solution did not work for me. Looks like I have a nice heavy paper weight on my hands.
- 05 Nov 2014 11:58
- Forum: 7750 SR
- Topic: 7750-SR message "Do not know what chassis type this is!"
- Replies: 2
- Views: 2481
7750-SR message "Do not know what chassis type this is!"
My company picked up some used 7750-SR and one of the units starts to boot and then gives me an error message stating "Do not know what chassis type this is!" and then it reboots. He is the complete output that I see before the unit reboots. Alcatel 7x50 Boot ROM. Copyright 2000-2005 Alcat...
- 05 May 2014 13:11
- Forum: Beginner's questions about the Common Hardware
- Topic: Alcatel Riverstone 15101 console access question
- Replies: 0
- Views: 1829
Alcatel Riverstone 15101 console access question
I have had no luck with finding anything about these units on Google, and so far I have only found sites selling them. I have two of these old Riverstone 15101 units and I can't get anything useful out of the console port. All that I get is junk. I am using putty, and I have tried a Cisco cable, a L...
- 13 Mar 2014 15:12
- Forum: OmniSwitch 6850 / 6850E
- Topic: No Console Output but web GUI works.
- Replies: 3
- Views: 1832
Re: No Console Output but web GUI works.
I have tried to get any sort of console output on two different system and I still get no output. I have heard that this issue could be caused by a flash upgrade that had failed.