Search found 11 matches

by rodos
29 Mar 2017 02:53
Forum: OmniStack LS 6200
Topic: 6200 visio stencils
Replies: 10
Views: 5596

Re: 6200 visio stencils

Can I also have them?

Thank you
by rodos
08 Mar 2012 09:42
Forum: OmniAccess 5510
Topic: SUM password
Replies: 2
Views: 1913

Re: SUM password

Hello,
In order to access with telne the OA you need to manage the enable password.

You need to do from the CLI and under config the following command:

enable secret xxxxxx

where xxxxx is the passwrod you would like to have on the enable.
by rodos
08 Mar 2012 09:35
Forum: OmniAccess 5510
Topic: VPN Mobile Worker Configuration
Replies: 6
Views: 2861

Re: VPN Mobile Worker Configuration

Hello, This feature is called "host to subnet" or "Road Warrior"on the OA (OmniAcess 5xxx). See page 922 on the OmniAccess_5510_USG_CLIConfigurationGuide_Release3.0.pdf Note that in order to achieve this you will need to install a RADIUS server which will work with the 5510. 5510 does not have the c...
by rodos
15 Jan 2009 08:42
Forum: H323 / Sip
Topic: PBX behind NAT
Replies: 8
Views: 3645

Re: PBX behind NAT

Hello, Sorry for not answering to you sooner. Yes it does exactly what you are talking about. The SBC has a public IP@ and the OXE is directly connected to the SBC. The SIP phones have as registra and proxy the public IP@ of the SBC and SBC is doing all the NAT transversing. You can have as many SIP...
by rodos
23 Oct 2008 07:05
Forum: MAIN
Topic: Cannot get PCM2 board In Service when Declared as IVR_Z30
Replies: 5
Views: 1126

Re: Cannot get PCM2 board In Service when Declared as IVR_Z30

Your problem was that you were using the old release of PCM boards which were not compatible with the Z IVR function
by rodos
23 Oct 2008 07:01
Forum: ON SITE TROUBLES
Topic: IVR calls can't reach CC agents.
Replies: 11
Views: 1667

Re: IVR calls can't reach CC agents.

I had a similar problem but the problem was that the IVR lines freezed. If this is what is happening to you then do the following: go in the CCIVR registry and make the following modifications: /system/CurrentControlSet/Control/SessionManager/Subsystems set in the key Windows : ...Windows SharedSect...
by rodos
23 Oct 2008 06:16
Forum: GENERAL
Topic: meet me conf problem
Replies: 4
Views: 855

Re: meet me conf problem

Check in the system parameters how many trunks can access the conference. The parameter is "Max. No Trks multi-p conference"
by rodos
23 Oct 2008 06:03
Forum: GENERAL
Topic: PRA Ports Block Issue
Replies: 12
Views: 1299

Re: PRA Ports Block Issue

Yes, synchronization could be a major issue.
Check with command infocs if you have any T2 synchronized with the PSTN. If not then managed the synchronization. As soon as you do it, the problem should be fixed
by rodos
23 Oct 2008 05:59
Forum: GENERAL
Topic: Echo
Replies: 12
Views: 2787

Re: Echo

Usually echo is due to bad VoIP quality (big delays) but sometimes echo can be also due to the presence of analogue equipment between two communications. So in the case of the calls through the PSTN you should ask for your public provider to check their equipment. As far as the VoIP issues in the sa...
by rodos
14 Oct 2008 04:01
Forum: H323 / Sip
Topic: PBX behind NAT
Replies: 8
Views: 3645

Re: PBX behind NAT

NeoTip has released a product called SBC which does excatly this job for Alcatel. You can buy this product directly from Alcatel. I am currently using this in one of my customers and it is doing excatly this and even more.

Go to advanced search