how to register other DECT handsets?

Everything about the PWT, IBS, RBS, DECT..

how to register other DECT handsets?

Postby junpeng » Sat Sep 20, 2008 6:34 am

Many of my company's mobile 100 has worn out and since Alcatel doesn't provide mobile 100/200 any longer, I want to use some other DECT phones. From here I know Siemens S45 or E45 can do the job well. But I don't know how to register these DECT phones. After reading Siemens gigaset S45 manual, I find S45 can register to at most 4 bases, and it needs base PIN and base number during the registration procedure. When registering a mobile 100, I choose "N" when asked which base to register, then it registers to all the base stations. By using dectarea, I found there are 16 base stations in my company. So, what should I do after choose GAP handset type and run dectinston -g command, how do I deal with these base number and base PIN issue. By the way, I have tried to register the mobile 100 in GAP mode, its procedure is just like the GAP+ mode, no need of base number and base PIN.
junpeng
Member
 
Posts: 3
Joined: Wed Sep 10, 2008 9:21 pm

Re: how to register other DECT handsets?

Postby junpeng » Sat Sep 20, 2008 6:42 am

Any other DECT handsets and their registration procedures are welcome
junpeng
Member
 
Posts: 3
Joined: Wed Sep 10, 2008 9:21 pm

Re: how to register other DECT handsets?

Postby vad » Sat Sep 20, 2008 11:02 pm

Create sets with GAP type.
Use dectinston Dir_number or dectinston -g command.
On GAP handset start registration procedure.

When you see on GAP handset Base1, 2 .. - this is not base (individual IBS or RBS)- this is system (like for mobile 100/200). You can register in Base1 f.e. on your PBX, Base2 f.e. at home and so on.
User avatar
vad
Alcatel Unleashed Certified Guru
Alcatel Unleashed Certified Guru
 
Posts: 2559
Joined: Thu Sep 23, 2004 3:47 am
Location: Russia

Re: how to register other DECT handsets?

Postby bouncer_ie » Sun Sep 21, 2008 4:44 am

would recommend kirk hansets as an alternative

http://www.kirktelecom.com/company/suk90.asp
bouncer_ie
 

Re: how to register other DECT handsets?

Postby junpeng » Wed Sep 24, 2008 6:54 pm

vad wrote:Create sets with GAP type.
Use dectinston Dir_number or dectinston -g command.
On GAP handset start registration procedure.

When you see on GAP handset Base1, 2 .. - this is not base (individual IBS or RBS)- this is system (like for mobile 100/200). You can register in Base1 f.e. on your PBX, Base2 f.e. at home and so on.


What about the PIN? I can't register S45 because it has no response. Is it the reason of the PIN. When asked to input PIN, I just input OK to use the default 0000. Or it is due to the weak signal, but I can easily register a Mobile 100 in GAP mode.
junpeng
Member
 
Posts: 3
Joined: Wed Sep 10, 2008 9:21 pm

Re: how to register other DECT handsets?

Postby vad » Wed Sep 24, 2008 8:22 pm

Usually when GAP set ask PIN you need to dial 0000 and OK (for Siemens).
User avatar
vad
Alcatel Unleashed Certified Guru
Alcatel Unleashed Certified Guru
 
Posts: 2559
Joined: Thu Sep 23, 2004 3:47 am
Location: Russia


Return to Wireless configuration and sets

Who is online

Users browsing this forum: No registered users and 1 guest

Creative Commons License
AlcatelUnleashed by AlcatelUnleashed is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.
Based on a work at www.AlcatelUnleashed.com.
AlcatelUnleashed is NOT affiliated with or endorsed by Alcatel-Lucent.
Contact: info at alcatelunleashed.com
RSS FEED