Create a service from one CE to the other via VPRN

[thakadbd]

I have successfully created the VPRN service. I have two CE which are connected to the VPRN and the routing protocol between the CE and PE routers have been done successfully. Using the command oam vpn-ping service-id source x.x.x.x destination y.y.y.y I am able to verify that the VPRN works. I want to create a service that will originate on one CE and terminate on the other CE via the VPRN and until now I cannot figure out how to do this.

Also when I ping the remote CE from one CE I am getting an error message.

[thakadbd]

I think the solution is in configuring ospf export policy to on the CE to advertise the system address and configure the export policy on the PE to advertise the VPN. Can anyone show me how to accomplish these task.

[hbaloi]

Hello,

I have a VPRN configured between on SAR18 and another SR7 at far end . But the service randomly goes down and i have do reboot the SAR18 to restore it.
Any idea in how to solve it definitely ?

Regards

[Stoffen]

Hello,

I have a VPRN configured between on SAR18 and another SR7 at far end . But the service randomly goes down and i have do reboot the SAR18 to restore it.
Any idea in how to solve it definitely ?

Regards

Hi.
Its not easy to say how to solve this with no information.

Is it only one particular VPRN service that suffers from this problem, or does it affect all/other services on SAR18 as well?
Any information in log when the problem occurs?

Can you give us the output from "show service id <id> all" when the problem is present?

[hbaloi]

Dear Chris,

Thank you for your reply . But this one was sorted out ( it was the microwave link tha was flapping, causing detours and blocks ).

The out of the service was always the same ( never down ) :

A:Benfica# show service id 3312601 base

===============================================================================
Service Basic Information
===============================================================================
Service Id : 3312601
Service Type : VPRN
Name : IuB_MHRNC03
Description : IuB over IP VPRN to MHRNC03
Customer Id : 1
Last Status Change: 12/16/2016 09:49:58
Last Mgmt Change : 12/16/2016 09:49:58
Admin State : Up Oper State : Up

Route Dist. : 65000:3312601117 VPRN Type : regular
AS Number : 65000 Router Id : 10.1.16.117
ECMP : Enabled ECMP Max Routes : 1
Max IPv4 Routes : No Limit Auto Bind : None
Max IPv6 Routes : No Limit
Ignore NH Metric : Disabled
Vrf Target : target:65000:33126*
Vrf Import : None
Vrf Export : None
MVPN Vrf Target : None
MVPN Vrf Import : None
MVPN Vrf Export : None

SAP Count : 14 SDP Bind Count : 1

-------------------------------------------------------------------------------
Service Access & Destination Points
-------------------------------------------------------------------------------
Identifier Type AdmMTU OprMTU Adm Opr
-------------------------------------------------------------------------------
sap:1/3/1:2198 q-tag 1518 1518 Up Up
sap:1/3/2:2150 q-tag 1518 1518 Up Up
sap:1/3/8:2080 q-tag 1518 1518 Up Up
sap:1/3/8:2123 q-tag 1518 1518 Up Up
sap:1/4/1:2199 q-tag 1518 1518 Up Up
sap:1/4/1:2221 q-tag 1518 1518 Up Up
sap:1/4/2:2197 q-tag 1518 1518 Up Up
sap:1/4/5:2124 q-tag 1518 1518 Up Up
sap:1/4/6:2153 q-tag 1518 1518 Up Up
sap:1/5/2:2014 q-tag 1518 1518 Up Up
sap:1/5/3:2044 q-tag 1518 1518 Up Up
sap:1/5/4:2174 q-tag 1518 1518 Up Up
sap:1/5/5:2143 q-tag 1518 1518 Up Up
sap:1/5/6:2099 q-tag 1518 1518 Up Up
sdp:126:3312601 S(10.1.16.126) n/a 0 1546 Up Up
===============================================================================
* indicates that the corresponding row element may have been truncated.
A:Benfica#



Logs :

[hbaloi]

Hi Friends,

Im tyring to config an E1 inside a STM1, with channel-group 1 using encap-ppp, and im getting the error below. Can anyone help :

*A:MHBHR01>config>port>tdm>e1>channel-group# encap-type ppp-auto
MINOR: PMGR #1005 Invalid value - 1/2/4.1.1.1.1, Invalid Mode access or Encap ppp-auto

[mivens]

ppp-auto is only valid if the port is in network mode.
Is it configured as an access port?