UniDirectional Link Detection (UDLD) in aggressive mode.
Also you can try to create a LACP (only one port attached). The port will leave the LAG if the LACPDU from the other site will not received anymore.
Search found 1891 matches
- 19 May 2024 08:17
- Forum: OmniSwitch 6450
- Topic: OS6450-10 | Requires a function similar to LLF
- Replies: 1
- Views: 82
- 16 May 2024 02:13
- Forum: OmniSwitch 6900
- Topic: VLAN isolation
- Replies: 3
- Views: 118
Re: VLAN isolation
To forbid routing you need only to configure the rules at the router.
But I prefer to configure the rules at the edge too. For this you can use OV (f.e. with cli scripts) to configure all access switches in one step.
But I prefer to configure the rules at the edge too. For this you can use OV (f.e. with cli scripts) to configure all access switches in one step.
- 16 May 2024 02:10
- Forum: OmniSwitch 6900
- Topic: Virtual-Chassis of OS6900-X40 & OS6900-X48
- Replies: 3
- Views: 103
Re: Virtual-Chassis of OS6900-X40 & OS6900-X48
correct. The old hardware (X20/40, T20/40, X72/Q32) can be connected in one VC up to 6. And all new switches too (X24/48, T24/48, V72, C32). But the old switches and the new one can not connected together in one VC.
BR Silvio
BR Silvio
- 14 May 2024 13:37
- Forum: OmniSwitch 6900
- Topic: VLAN isolation
- Replies: 3
- Views: 118
Re: VLAN isolation
You need routing and you need policies. The policies you should configure at your router=gateway (switch or firewall).
For you private-vlan is not a solution. You need ACL/policies.
BR Silvio
For you private-vlan is not a solution. You need ACL/policies.
BR Silvio
- 03 May 2024 12:12
- Forum: OmniSwitch 6900
- Topic: CLI Message
- Replies: 2
- Views: 324
Re: CLI Message
difficult to understand this. For real clearance you need to open a ticket (maybe you find something in the knowledgebase in myportal). - svc means service (used for SPB or VxLAN). - 1010 means port 1/1/1 - accessport is an unp port type access - info -> this isn't a problem maybe a misconfiguration
- 28 Apr 2024 12:08
- Forum: OmniSwitch 2260 / 2360
- Topic: oversize frames on fiber port
- Replies: 2
- Views: 212
Re: oversize frames on fiber port
I am wondering about the same value for RX Oversize and CRC at all the ports. I assume the oversize is an display issue - you need to check with ALE support (but only with actal AOS release). CRC is mostly bad fibre connection (dirty connectors etc.). Use other connections/patchcables (if possible)....
- 28 Apr 2024 11:56
- Forum: OmniSwitch 9900
- Topic: Reload Working configuration without reboot
- Replies: 3
- Views: 260
Re: Reload Working configuration without reboot
maybe the syntax is not fully correct (not checked it). Use the tab-key to find out the correct syntax.
- 25 Apr 2024 14:47
- Forum: OmniSwitch 9000 / 9000E
- Topic: static route from source IP to destination
- Replies: 2
- Views: 238
Re: static route from source IP to destination
This is possible (named PBR - policy based routing). Search in the guides (or here in the forum) for "policy action permanent-gateway".
BR Silvio
BR Silvio
- 25 Apr 2024 14:45
- Forum: OmniSwitch 6860 / 6860E
- Topic: Disable TCP services on switch
- Replies: 3
- Views: 512
Re: Disable TCP services on switch
I know only the predifined services like telnet, ssh...
Search in cli-guide or open a ticket.
BR Silvio
Search in cli-guide or open a ticket.
BR Silvio
- 25 Apr 2024 14:43
- Forum: OmniSwitch 6850 / 6850E
- Topic: Can I use 510W power for a 6850E(non-poe switch)
- Replies: 1
- Views: 155
Re: Can I use 510W power for a 6850E(non-poe switch)
Try it. It should work